23/07/2024 17:24:59

Air Suspension Compressor and Reservoir - Carrier Bracket - Air Suspension Compressor (Remove and Install)

Correction code 3110008021 3110008022 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Put the vehicle in Service Mode. See Service Mode.
  3. Unlock the vehicle gateway. See Gateway (Unlock).
  4. Fully depressurize the air suspension. See Air Suspension - Pressurize / Depressurize - Full System.
  5. Open the tonneau cover.
  6. Open the tailgate.
  7. Remove the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  8. Disconnect the VOSS fitting, and then remove the rear air line from the air compressor.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm 12 point combination wrench
    Informational PurposesAn informational icon, calling your attention
    Note
    Discard the air line fitting after removal.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the air line removal tool (1706517-00-A) to release the inlet air line hose
  9. Release the clips (x4) and disconnect the air compressor harness electrical connectors (x3).
  10. Remove the nuts (x3) that attach the air suspension compressor carrier bracket to the body.
    12 Nm (8.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm deep socket
  11. Remove the bolts (x4) that attach the air suspension compressor carrier bracket to the air compressor, and then remove the bracket from the vehicle.
    5.5 Nm (4.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket

Install

  1. Install the bolts (x4) that attach the air suspension compressor carrier bracket to the air compressor.
    5.5 Nm (4.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
  2. Install the nuts (x3) that attach the air suspension compressor carrier bracket to the body.
    12 Nm (8.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm deep socket
  3. Fasten the clips (x4) and connect the air compressor harness electrical connectors (x3).
  4. Install the rear air line to the air compressor.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    Informational PurposesAn informational icon, calling your attention
    Note
    x1 VOSS fitting
    Informational PurposesAn informational icon, calling your attention
    Note
    Install new VOSS fitting.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove the white plug when the airline is ready to be installed.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fully insert the airline into fitting. It should sit between the two white marks on the airline. Verify the airline is properly seated by performing a push-pull test.
  5. Install the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  6. Close the tonneau cover.
  7. Close the tailgate.
  8. Refill the air suspension with nitrogen. See Air Suspension - Pressurize / Depressurize - Full System.
  9. Exit Service Mode. See Service Mode.
  10. Raise the LH front window and close the LH front door.