23/10/2024 09:25:23

Tonneau - LH Tonneau Motor Assembly (Remove and Install)

Correction code 1120122021 1120122022 1120122031 1120122032 FRT 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-10-23: Rearranged steps to ease removal/installation of sail applique.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the tonneau cover.
  2. Open the tailgate.
  3. Remove the LH sail applique assembly. See Truck Bed Exterior Trim - Sail Applique Assembly - LH (Remove and Replace).
  4. Remove the LH tonneau water management seal. See Tailgate Seals - Tonneau Water Management Seal, LH, Center (Remove and Install).
  5. Remove the truck bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  6. Remove the bed cargo tub struts. See Tonneau - Bed Cargo Tub Strut (Remove and Install).
  7. Remove the bolts (x4) that attach the bed cargo tub lid.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance.
  8. Remove the LH upper bed side wall assembly. See Truck Bed Exterior Trim - Upper Bed Side Wall Assembly - LH (Remove and Install).
  9. Remove the LH rear bed closeout. See Truck Bed - Rear Bed Closeout - LH (Remove and Install).
  10. Remove the LH bed side wall. See Bed Side Wall - Bed Side Wall - LH (Remove and Install).
  11. Disconnect the LH tonneau motor electrical connector, and then remove the bolts (x2) that attach the motor to the body,
    11 Nm (8.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket

Install

  1. Install the bolts (x2) that attach the LH tonneau motor to the body, and then connect the electrical connector.
    11 Nm (8.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  2. Install the LH bed side wall. See Bed Side Wall - Bed Side Wall - LH (Remove and Install).
  3. Install the LH rear bed closeout. See Truck Bed - Rear Bed Closeout - LH (Remove and Install).
  4. Install the LH upper bed side wall assembly. See Truck Bed Exterior Trim - Upper Bed Side Wall Assembly - LH (Remove and Install).
  5. Install the bolts (x4) that attach the bed cargo tub lid.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance.
    Informational PurposesAn informational icon, calling your attention
    Note
    Position the bed cargo tub lid onto the vehicle. Install the bolts that attach the bed cargo tub lid onto the hinges.
  6. Install the bed cargo tub struts. See Tonneau - Bed Cargo Tub Strut (Remove and Install).
  7. Install the truck bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  8. Install the LH tonneau water management seal. See Tailgate Seals - Tonneau Water Management Seal, LH, Center (Remove and Install).
  9. Install the LH sail applique assembly. See Truck Bed Exterior Trim - Sail Applique Assembly - LH (Remove and Replace).
  10. Close the tonneau cover.
  11. Close the tailgate.