23/07/2024 17:31:55

Interior Ducting and Vents - Demist Duct Asssembly - Passenger (Remove and Install)

Correction code 1405077091 1405077092 FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Open the RH front door and lower the RH front window.
  3. Remove the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  4. Remove the LH lower A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install).
  5. Remove the footwell cover. See Dash Support Frame - Footwell Cover (Remove and Install).
  6. Remove the RH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  7. Remove the RH lower A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install).
  8. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  9. Disconnect MV power. See Disconnect MV Power.
  10. Remove the mid instrument panel assembly. See Dash Panel - IP Mid Panel Assembly (Remove and Install).
  11. Remove the lower IP assembly. See Dash Panel - Instrument Panel Lower Assembly (Remove and Install).
  12. Remove the glovebox assembly. See Dash Panel - IP Glovebox Assembly (Remove and Install).
  13. Remove the RH panel duct. See Passenger Ducting and Vents - Panel Duct, RH (Remove and Install).
  14. Remove the passenger airbag. See Front Air Bags - MX - Passenger Airbag, NAR (Remove and Install).
  15. Remove the instrument panel top pad assembly. See Dash Panel - Instrument Panel Top Pad Assembly (Remove and Install).
  16. Remove the RH IP quarter panel. See Dash Panel - Quarter Panel Assembly - LH (Remove and Install).
  17. Remove the RH quarter glass demist duct. See Passenger Ducting and Vents - Quarter Glass Demist Duct, LH (Remove and Install).
  18. Remove the clips (x2) that attach the passenger demist duct assembly to the vehicle, and then remove the duct from the vehicle.

Install

  1. Position the passenger demist duct into the vehicle, and then install the clips (x2) that attach the duct to the vehicle.
  2. Install the RH quarter glass demist duct. See Passenger Ducting and Vents - Quarter Glass Demist Duct, LH (Remove and Install).
  3. Install the RH IP quarter panel. See Dash Panel - Quarter Panel Assembly - LH (Remove and Install).
  4. Install the instrument panel top pad assembly. See Dash Panel - Instrument Panel Top Pad Assembly (Remove and Install).
  5. Install the passenger airbag. See Front Air Bags - MX - Passenger Airbag, NAR (Remove and Install).
  6. Install the RH panel duct. See Passenger Ducting and Vents - Panel Duct, RH (Remove and Install).
  7. Install the glovebox assembly. See Dash Panel - IP Glovebox Assembly (Remove and Install).
  8. Install the lower IP assembly. See Dash Panel - Instrument Panel Lower Assembly (Remove and Install).
  9. Install the mid instrument panel assembly. See Dash Panel - IP Mid Panel Assembly (Remove and Install).
  10. Reconnect MV power. See Disconnect MV Power.
  11. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  12. Install the RH lower A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install).
  13. Install the RH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  14. Install the footwell cover. See Dash Support Frame - Footwell Cover (Remove and Install).
  15. Install the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  16. Install the LH lower A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install).
  17. Raise the RH front window and close the RH front door.
  18. Raise the LH front window and close the LH front door.