23/07/2024 17:29:40

Front Energy Absorber - Front Bumper Beam Assembly (Remove and Install)

Correction code 1001050011 1001050012 FRT 1.02 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. On the touchscreen, touch Controls > Suspension > Very High to set the vehicle ride height to Very High.
  3. Place the vehicle into Service Mode. See Service Mode.
  4. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  5. Disconnect MV power. See Disconnect MV Power.
  6. Remove the frunk assembly. See Frunk Assembly (Remove and Install).
  7. Remove the center applique assembly. See Front Grille and Applique - Front Center Applique Assembly (Remove and Install).
  8. Remove the front fascia assembly. See Front Bumper Fascia - Front Fascia (Remove and Install).
  9. Remove the LH and RH headlight assemblies. See Headlamps - Headlamp Assembly - LH (Remove and Install).
  10. Remove the powergate latch assembly. See Latch - Powergate (Remove and Replace).
  11. Remove the front end carrier. See Front Bumper Carrier - Front End Carrier Plastic Assembly (Remove and Install).
  12. Remove the LH support bracket. See Front Energy Absorber - Support Bracket - LH (Remove and Install).
  13. Remove the front BLE end point. See Remote and Passive Entry - Front Rear BLE Gen 3 (Remove and Install).
  14. Remove the RH support bracket. See Front Energy Absorber - Support Bracket - LH (Remove and Install).
  15. Remove the front center support bracket. See Front Energy Absorber - Support Bracket - Center (Remove and Install).
  16. Remove the nuts (x4) that attach the front bumper beam assembly to the vehicle, and then remove the assembly from the vehicle.
    30 Nm (22.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket

Install

  1. Position the front bumper beam assembly onto the vehicle, and then install the nuts (x4) that attach the assembly to the vehicle.
    30 Nm (22.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
  2. Install the front center support bracket. See Front Energy Absorber - Support Bracket - Center (Remove and Install).
  3. Install the RH support bracket. See Front Energy Absorber - Support Bracket - LH (Remove and Install).
  4. Install the front BLE end point. See Remote and Passive Entry - Front Rear BLE Gen 3 (Remove and Install).
  5. Install the LH support bracket. See Front Energy Absorber - Support Bracket - LH (Remove and Install).
  6. Install the front end carrier. See Front Bumper Carrier - Front End Carrier Plastic Assembly (Remove and Install).
  7. Install the powergate latch assembly. See Latch - Powergate (Remove and Replace).
  8. Install the LH and RH headlight assemblies. See Headlamps - Headlamp Assembly - LH (Remove and Install).
  9. Install the front fascia assembly. See Front Bumper Fascia - Front Fascia (Remove and Install).
  10. Install the frunk assembly. See Frunk Assembly (Remove and Install).
  11. Reconnect MV power. See Disconnect MV Power.
  12. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  13. Raise the LH front window and close the LH front door.