23/07/2024 17:30:25

Front Seat Sliders and Controllers - 1R Seat Inboard Riser LH (Remove and Replace)

Correction code 1301061051 1301061052 1301061071 1301061072 FRT 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-03-07: Added torque values for inboard riser to vehicle and inboard riser to crossmember.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the RH front door and lower the RH front window.
  2. Move the RH front seat fully forward.
  3. Remove the center console rear panel. See Center Console - Back Panel Assembly (Remove and Install).
  4. Remove the bolts (x2) that attach the rear of the center console to the riser.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Move the RH front seat fully rearward.
  6. Remove the RH center floor rail. See Passenger Compartment Carpet - Center Floor Rail - LH (Remove and Install).
  7. Remove the LH front seat assembly. See Front Seat Assemblies - 1st Row Seat Assembly - LH Drive - LH - Black (Remove and Install).
  8. Remove the LH center floor rail. See Passenger Compartment Carpet - Center Floor Rail - LH (Remove and Install).
  9. Remove the center console. See Center Console - Center Console Assembly (Remove and Install).
  10. Remove the bolt that attaches the LH front seat outboard riser to the crossmember.
    35 Nm (25.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
  11. Remove the bolts (x2) that attach the LH inboard seat riser to the crossmember.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  12. Release the clips (x2) that attach the rear cabin carpet to the LH front cabin carpet.
  13. Remove the driver carpet assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    The plastic portions at the rear of the carpet need to clear risers.
  14. Use a trim tool to release the clips (x6) that attach the LH front seat inboard riser cover to the riser, and then remove the cover from the riser.
  15. Release the clips (x2) that attach the rearward duct to the inboard riser, and then remove the duct from the riser.
  16. Remove and discard the bolts (x2) that attach the LH front seat inboard riser to the vehicle, and then remove the riser from the vehicle.
    40 Nm (29.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket

Install

  1. Position the LH front seat inboard riser into the vehicle, and then install new bolts (x2) that attach the riser to the vehicle.
    40 Nm (29.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
  2. Position the rearward duct into the inboard riser, and then install the clips (x2) that attach the duct to the riser.
  3. Position the LH front seat inboard riser cover to the riser, and then engage the clips (x6) that attach the cover to the riser.
    Informational PurposesAn informational icon, calling your attention
    Note
    Start from the bottom of the cover and work upward.
  4. Install driver carpet assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    The plastic portions at the rear of the carpet need to clear risers.
  5. Secure the clips (x2) that attach the rear cabin carpet to the LH front cabin carpet.
  6. Install the bolts (x2) that attach the LH inboard seat riser to the crossmember.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Install the bolt that attaches the LH front seat outboard riser to the crossmember.
    35 Nm (25.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
  8. Install the center console. See Center Console - Center Console Assembly (Remove and Install).
  9. Install the LH front seat assembly. See Front Seat Assemblies - 1st Row Seat Assembly - LH Drive - LH - Black (Remove and Install).
  10. Raise the RH rear window and close the RH rear door.
  11. Restore the RH front seat back to its original position.
  12. Raise the RH front window and close the RH front door.