23/07/2024 17:29:03

Front Brake Rotors - Calipers and Pads - Front Brake Caliper - LH (Remove and Install)

Correction code 3301044021 3301044022 3301044031 3301044032 FRT 0.71 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Raise and support the vehicle on a 2 post lift. See Raise Vehicle - 2 Post Lift.
  3. Open the powered frunk.
  4. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  5. Remove the LH front wheel cap. See Wheel Cover - Front - LH (Remove and Install).
  6. Loosen the LH front wheel lug nuts (x6).
    205 Nm (151.2 lbs-ft)
    .
    Tip: Use of the following tool(s) is recommended:
    • 21 mm deep socket
  7. Raise the vehicle fully.
  8. Remove the nuts (x6) that attach the wheel to the hub, and then remove the wheel from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 21 mm deep socket
  9. Remove the bolt that attaches the LH front brake hose bracket to the knuckle.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
  10. Position an oil drain underneath the LH front brake hose.
  11. Remove the bolt that attaches the hose to the LH front brake caliper.
    42 Nm (31.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm deep socket
  12. Remove the bolts (x2) that attach the LH front caliper to the knuckle.
    315 Nm (232.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 24 mm socket

Install

  1. Install the bolts (x2) that attach the LH front caliper to the knuckle.
    315 Nm (232.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 24 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance.
    Informational PurposesAn informational icon, calling your attention
    Note
    The rotor will be loose until the caliper is installed.
  2. Install the bolt that attaches the hose to the LH front brake caliper.
    42 Nm (31.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm deep socket
  3. Install the bolt that attaches the LH front brake hose bracket to the knuckle.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
  4. Remove the oil drain from underneath the vehicle.
  5. Bleed the LH front caliper. See Brake Fluid Bleed - One Caliper.
  6. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  7. Install the LH front wheel cap. See Wheel Cover - Front - LH (Remove and Install).
  8. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install)
  9. Close the powered frunk.
  10. Remove the vehicle from the lift. See Raise Vehicle - 2 Post Lift.
  11. Raise the LH front window and close the LH front door.
  12. Perform a road test and burnish the brakes.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure proper brake pedal feel and performance.