23/07/2024 17:36:04

Inspect Underbody Fastener Torque

Correction code NA NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Procedure

  1. Open the LH front door and lower the LH front window.
  2. On the vehicle touchscreen, navigate to Controls > Ride Height > Very High to set the air suspension ride height to “Very High”.
  3. Navigate to Service > Jack Mode to place the air suspension into "Jack Mode".
  4. Remove the LH and RH rocker covers. See Rocker Panel Trim - Rocker Assembly - LH (Remove and Install).
  5. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  6. Raise the vehicle fully.
  7. Remove the LH and RH lower tow eye cap. See Front Grille and Applique - Lower Tow Eye Cap - LH (Remove and Replace).
  8. Remove the front fascia plastic skid plate. See Undertray - Skid Plate (Remove and Install).
  9. Remove the front aero shield. See Undertray - Front Aeroshield (Remove and Install).
  10. Remove the fasteners that attach the front skid plate to the vehicle, and then remove the skid plate from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
    • 11 mm socket
  11. Remove the LH and RH front lower control arm shields. See Rear Suspension Arms - Rear Lower Arm Aeroshield - LH (Remove and Install).
    Informational PurposesAn informational icon, calling your attention
    Note
    Rear shields shown; front shields similar.
  12. Remove the rear aeroshield. See Undertray - Rear Aeroshield (Remove and Install).
  13. Remove the LH and RH rear lower control arm shields. See Rear Suspension Arms - Rear Lower Arm Aeroshield - LH (Remove and Install).
  14. Verify the bolts (x2) that attach the front chassis structure to the vehicle are torqued to specification.
    220 Nm (162.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 24 mm socket
  15. Verify the nuts (x4) that attach the front chassis structure to the vehicle are torqued to specification.
    215 Nm (158.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 24 mm socket
  16. Verify the bolts (x4) that attach the front chassis structure to the vehicle are torqued to specification.
    220 Nm (162.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 21 mm socket
  17. Verify the bolts (x4) that attach the LH and RH front air spring modules to the front lower control arms are torqued to specification.
    140 Nm (103.2 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If the fasteners are not torqued to specification, they must be replaced.
    Tip: Use of the following tool(s) is recommended:
    • 21 mm socket
  18. Verify the bolts (x16) that attach the HV battery to the vehicle are torqued to specification.
    62 Nm (45.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
  19. Verify the bolts (x6) that attach the HV battery to the vehicle are torqued to specification.
    115 Nm (84.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 18 mm socket
  20. Verify the bolts (x4) that attach the rear chassis structure to the vehicle are torqued to specification.
    355 Nm (261.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 24 mm socket
  21. Verify the bolts (x4) that attach the LH and RH rear air spring modules to the rear lower control arms are torqued to specification.
    140 Nm (103.2 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If the fasteners are not torqued to specification, they must be replaced.
    Tip: Use of the following tool(s) is recommended:
    • 21 mm socket
  22. Install the LH and RH rear lower control arm shields. See Rear Suspension Arms - Rear Lower Arm Aeroshield - LH (Remove and Install).
  23. Install the rear aeroshield. See Undertray - Rear Aeroshield (Remove and Install).
  24. Install the LH and RH front lower control arm shields. See Rear Suspension Arms - Rear Lower Arm Aeroshield - LH (Remove and Install).
  25. Position the front skid plate to the vehicle, and then install the fasteners that attach the skid plate to the vehicle.
    50 Nm (36.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
    • 11 mm socket
  26. Install the front aero shield. See Undertray - Front Aeroshield (Remove and Install).
  27. Install the front fascia plastic skid plate. See Undertray - Skid Plate (Remove and Install).
  28. Install LH and RH rocker covers. See Rocker Panel Trim - Rocker Assembly - LH (Remove and Install).
  29. Lower the vehicle until the tires are touching the ground.
  30. Remove the vehicle from the lift. See Raise Vehicle - 2 Post Lift.
  31. Install the LH and RH rocker covers. See Rocker Panel Trim - Rocker Assembly - LH (Remove and Install).
  32. On the vehicle touchscreen, navigate to Controls > Service > Jack Mode to remove the vehicle from "Jack Mode".
  33. On the vehicle touchscreen, navigate to Controls > Ride Height > Medium to set the suspension height to "Medium".
  34. Raise the LH front window and close the LH front door.