26/08/2022 03:56:27

Brake Lines - Master Cylinder to ABS (Structural Pack) (LHD) (Remove and Replace)

Correction code 33034012 1.62 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  4. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  5. Remove the 12V battery. See 12V/LV Battery (Remove and Replace).
  6. Remove front aero shield. See Panel - Aero Shield - Front (Structural Pack) (Remove and Replace).
  7. Disconnect the electrical connector from the ABS unit.
  8. Position the oil drain under the ABS unit.
  9. Loosen the nut that attaches the master cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  10. Loosen the nut that attaches the primary cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  11. Place an absorbent material beneath the brake booster and reservoir area.
  12. Using a brake fluid syringe, remove the brake fluid from the reservoir.
  13. Loosen the nut that attaches the secondary brake line to the master cylinder, and then remove the secondary brake line.
    16 Nm (11.8 lbs-ft)
  14. Loosen the nut that attaches the primary brake line to the master cylinder, and then remove the primary brake line.
    16 Nm (11.8 lbs-ft)
  15. Release the primary and secondary brake lines from the brake line bundle clip.
  16. Loosen the harness clip that attaches the master cylinder brake lines to the rear of the hydraulic control unit bracket.
  17. Route the master cylinder brake lines towards the front controller, and then remove the master cylinder brake line bundle from the vehicle.

Install

  1. Place the master cylinder brake line bundle into position for installation
  2. Install the secondary brake line to the master cylinder, and then fasten the nut that attaches the secondary brake line.
    16 Nm (11.8 lbs-ft)
  3. Install the primary brake line to the master cylinder, and then fasten the nut that attaches the primary brake line.
    16 Nm (11.8 lbs-ft)
  4. Remove the absorbent material from underneath the brake booster and brake fluid reservoir area.
  5. Install the harness clip that attaches the master cylinder brake lines to the rear of the hydraulic control unit bracket.
  6. Attach the primary and secondary brake lines to the brake line bundle clip.
  7. Fasten the nut that attaches the master cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  8. Fasten the nut that attaches the primary cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  9. Clean the ABS unit surface of residual brake fluid.
  10. Remove the oil drain container from underneath vehicle
  11. Reconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  12. Bleed the brakes. See Brake Fluid Bleed/Flush
  13. Install the front aero shield. See Panel - Aero Shield - Front (Structural Pack) (Remove and Replace).
  14. Install the HEPA filter. See Assembly - Filter - HEPA (Remove and Replace).
  15. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  16. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  17. Perform a test drive.
    Informational PurposesAn informational icon, calling your attention
    Note
    Per current FRT (00040100) 0.3 hrs, If alignment was adjusted verify tracking, If DAS components were adjusted verify operation, If brakes were serviced perform burnishing