01/04/2024 13:58:57

Hose - Inlet - Radiator (Remove and Replace)

Correction code 18302612 0.96 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  2. Remover the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  4. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  5. Remove the front aero shield panel. See Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
  6. Remove the front fascia valance. See Valance - Front Fascia (Remove and Replace).
  7. Lower the vehicle fully.
  8. Place a fluid catcher underneath the front of the vehicle.
  9. Release clips that attach the radiator inlet hose to the vehicle.
  10. Release the spring clip that attaches the coolant hose to the radiator inlet, remove the hose from the radiator, and then plug the male and female fittings.
  11. Release the spring clip that attaches the radiator inlet hose to the supermanifold, and then remove the hose from the supermanifold.

Install

  1. Install the radiator inlet hose onto the Supermanifold, and then install the spring clip.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform push-pull-push test to make sure hose is fully seated.
  2. Install the radiator inlet hose onto the radiator, and then install the spring clip.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform push-pull-push test to make sure hose is fully seated
  3. Install the clips that attach the radiator inlet hose to the vehicle.
  4. Remove fluid catcher from underneath vehicle.
  5. Install the front fascia valance. See Valance - Front Fascia (Remove and Replace).
  6. Install the front aero shield panel. See Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
  7. Remove coolant bottle cap, and then fill coolant to the proper level.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the fluid level is filled to the Max line.
  8. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  9. Connect to the vehicle using a laptop with Toolbox 3.0.
  10. Click the Actions/Autodiag tab and search for "Purge".
  11. Click TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGESearch for routine in ToolboxThermal / Coolant System - Coolant Purge Starthv / Front Drive Inverter Replacement - Coolant Air Purgehv / Rear Drive Inverter Replacement - Coolant Air Purgehv / Rear Left Drive Inverter Replacement - Coolant Air Purgehv / Rear Right Drive Inverter Replacement - Coolant Air Purgehv / Front Drive Unit Replacement - Coolant Air Purgehv / Rear Drive Unit Replacement - Coolant Air PurgeThermal / Actions - Coolant Purge Stop or Coolant Purge Start, and then click Run and allow routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure vehicle is not in drive state. Plan is still running despite the stop message. Coolant pumps will be audible. Test lasts approximately 10 mins. Coolant pump speeds can be monitored in Service Mode + (see Service Mode Plus), in the CAN Viewer submenu. Idle speed = ~1500 RPM. Test will vary speeds from 3500-6500 RPM and actuate valve between SERIES and PARALLEL. Putting the vehicle into drive state will stop this routine. If speeds hover at 7000 RPM, that means the pumps are air locked, perform vacuum fill again. Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle. Select ‘X’ at top right of window to close once complete
  12. Remove the laptop from the vehicle.
  13. Inspect coolant level and top off as necessary
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the fluid level is at the Max level.
  14. Install coolant bottle cap.
  15. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  16. Remove the vehicle from the lift. See Raise Vehicle - 2 Post Lift.