26/09/2024 09:11:36

Seat Assembly - 1st Row - LH (Remove and Replace)

Correction code 13040102 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.
Informational PurposesAn informational icon, calling your attention
Note
The front seats contain airbags and pretensioners and therefore must be disposed of properly. See Remove the Front Seat Airbag and Discard for more information. Add Correction Code 20010707 to document the labor; the labor time for destructively removing and disposing of the front seat airbag and pretensioner is not reflected in the front seat removal and replacement labor time.
Informational PurposesAn informational icon, calling your attention
Note
Though the 1st row LH seat is described, the procedure is the same for the 1st row RH seat. This procedure can be used for the driver seat and the passenger seat in LHD and RHD vehicles.
Figure 1. Model 3 shown; Model Y similar
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  • 1133787-00-A Key, Seat Belt Release, Model 3
  • 1082447-07-A Torx Plus T45
  • 2024-09-26: Updated step for OCS self calibration routine.
  • 2023-07-03: Added steps to remove and install the front and rear seat track covers and updated steps for software reinstall and seat calibration.

Torque Specifications

Table 1. Torque Specifications: Seat Assembly - 1st Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Front seat to body bolt
33.5 Nm (24.7 lbs-ft)
  • Torx Plus T45 socket
  • 3/8 in std flex head ratchet
  • 3/8 in flex head torque wrench (installation only)
Replace Bolts are patched

Remove

  1. Open all the doors and lower all the windows.
  2. If servicing the front passenger seat:
    1. Place the vehicle into Service Mode. See Service Mode.
    2. Unlock the vehicle gateway. See Gateway (Unlock).
    3. Reinstall the vehicle software. See Software Reinstall - Touchscreen.
  3. Remove the LH mid A-Pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  4. Remove the LH lower A-Pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  5. Release the clip that attaches the LH front carpet to the body near the front of the LH door opening.
  6. Fold the front of the LH front carpet rearward so that the LH body controller module and its surrounding connectors are exposed.
  7. Insert the seat belt release key (1133787-00-A) into the bottom of the seatbelt pretensioner coupling to release the seatbelt from the pretensioner.
  8. Move the seat fully forward.
  9. Remove the driver seat track rear covers. See Cover - Rear - Seat Track - 1st Row Seat (Remove and Replace).
  10. Remove and discard the bolts (x2) that attach the rear of the 1st row LH seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • 3/8 in std flex head ratchet
    • 3/8 in flex head torque wrench (installation only)
  11. Move the seat fully rearward.
  12. Remove the driver seat track front covers. See Cover - Front - Seat Track - 1st Row Seat (Remove and Replace).
  13. Remove and discard the bolts (x2) that attach the front of the 1st row LH seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • 3/8 in std flex head ratchet
    • 3/8 in flex head torque wrench (installation only)
  14. Adjust the LH front seat to the middle of the seat tracks, and then raise the seat fully.
    Tip: Performing this step will aide in removing the seat.
  15. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  16. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  17. Locate the LH front seat electrical connector on the LH body controller module.
  18. Release the LH front seat connector lock, and then remove the connector from the LH body controller.
    Informational PurposesAn informational icon, calling your attention
    Note
    Squeeze the release tab on the LH front seat connector lock, and then swing the lock away from the connector to release the lock.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not pull on the connector too hard. If the connector does not easily disconnect from the LH body controller, the lock is still engaged.
  19. Release the clips (x2) that attach the LH front seat harness to the LH footwell support bracket near the LH side of the LH footwell.
  20. Release the clips that attach the LH front seat harness to the LH front seat harness guide.
  21. Pull the LH front seat harness out from under the LH front carpet.
  22. With assistance, remove the seat from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift the seat, tilt the seat back, rotate the cushion toward the front door, and remove the seat from the vehicle, cushion first.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take care not to damage the upholstery or trim while removing the seat.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If reinstalling the seat, place the seat in an area where it is not likely to be tipped over or otherwise damaged.

Install

  1. With assistance, position the 1st row LH seat in the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take care not to damage the upholstery or trim while positioning the seat.
  2. Route the 1st row LH seat harness under the LH front carpet, position the harness in the harness guide, and then install the clips that attach the harness to the harness guide.
  3. Install the clips (x2) that attach the LH front seat harness to the LH footwell support bracket near the LH side of the LH footwell.
  4. Install the LH front seat harness connector on the LH body controller, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform a push-pull test to ensure that the connector is fully seated and locked.
  5. Unfold the LH front carpet back into position, and then install the clip that attaches the carpet to the body near the front of the LH door opening.
  6. Install the LH lower A-Pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  7. Install the LH mid A-Pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  8. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  9. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  10. Move the LH front seat fully rearward.
  11. Install the new bolts (x2) that attach the front of the 1st row LH seat to the body.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • 3/8 in std flex head ratchet
    • 3/8 in flex head torque wrench (installation only)
  12. Install the driver seat track front covers. See Cover - Front - Seat Track - 1st Row Seat (Remove and Replace).
  13. Move the LH front seat fully forward.
  14. Install the LH 1st row seatbelt retractor onto the pretensioner.
    Informational PurposesAn informational icon, calling your attention
    Note
    After reinstalling the seatbelt pretensioner into the seatbelt pretensioner coupling, perform a pull test to make sure that the seatbelt and pretensioner are securely engaged.
  15. Install the new bolts (x2) that attach the rear of the 1st row LH seat to the body.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • 3/8 in std flex head ratchet
    • 3/8 in flex head torque wrench (installation only)
  16. Install the seat track rear covers. See Cover - Rear - Seat Track - 1st Row Seat (Remove and Replace).
  17. If servicing the driver seat:
    1. Use the vehicle touchscreen to place the vehicle into Service Mode. See Service Mode.
    2. Reinstall the vehicle software. See Software Reinstall - Touchscreen.
    3. On the vehicle touchscreen, touch Controls > Service > Driver Seat, Steering & Mirrors Calibration > Start.
    4. Exit Service Mode. See Service Mode.
  18. If servicing the front passenger seat in a North American vehicle:
    1. Consult the parts catalog to see if a configuration change is needed.
    2. Reinstall the vehicle software. See Software Reinstall - Touchscreen.
    3. Remove all objects from the front passenger seat before beginning calibration.
    4. Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
    5. Unlock the vehicle gateway. See Gateway (Unlock).
    6. In Toolbox, click on the Actions tab, and then search for "OCS".
    7. Run the PROC_OCS1P_SELF-CALIBRATIONSearch for routine in ToolboxSafety & Restraints / Seats - OCS1P Self Capacitance Calibration routine.
      Informational PurposesAn informational icon, calling your attention
      Note
      This routine is only necessary for Fremond built vehicles.
    8. Click on the Actions tab, and then search for "Seat calibration".
    9. Run the PROC_VCRIGHT_SEAT-CALIBRATESearch for routine in Toolbox routine.
    10. Disconnect Toolbox and remove the laptop from the vehicle.
  19. Move the seat to its original position.
  20. Raise all the windows and close all the doors.