19/02/2021 13:32:29

Trim - Cushion - 2nd Row Seat - RH (7-Seat) (Remove and Replace)

Correction code 13080042 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Remove the RH 2nd row seat assembly. See Seat Assembly - 2nd Row - RH (7-Seat) (Remove and Replace).
  2. Remove the RH 2nd row seat toe kick cover.
  3. Remove the clip that attaches the RH 2nd row seat side shield to the cushion pan.
  4. Release the clip that attaches the RH 2nd row seat side shield to the RH 2nd row seat assembly, and then lift the shield up to release it from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not pull the shield away from the assembly as there is still an electrical connector connected
  5. Disconnect the RH 2nd row seat side shield electrical connector, and then remove the shield from the assembly.
  6. Release the clips (x4) that attach the RH 2nd row seat outer B-cover from the inner B-cover, and slide the cover towards the rear of the seat to remove it from the assembly.
  7. Fold the seat to the upright position.
  8. Remove the screw that attaches the RH 2nd row seat inner B-cover to the cushion pan.
    1.5 Nm (1.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
  9. Release the hook that attaches the inner B-cover to the RH 2nd row seat assembly.
  10. Disconnect the LH 2nd row seatback harness electrical connector.
  11. Release the clip that attaches the RH 2nd row seat cushion harness connector to the seat frame.
  12. Disconnect the RH 2nd row seat RH floor latch electrical connector.
  13. Disconnect the RH 2nd row seat LH floor latch electrical connector.
  14. Disconnect the RH 2nd row seat seatbelt buckle electrical connector.
  15. Release the clip that attaches the RH 2nd row seat seatbelt buckle connector to the cushion pan.
  16. Disconnect the RH 2nd row seat seat track position sensor electrical connector.
  17. Release the clips that attach the RH 2nd row seat cushion harness to the podium.
  18. Remove the bolts that attach the RH 2nd row seat cushion pan to the seat frame.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  19. Remove the clip that attaches the RH 2nd row seat cushion pan to the seat frame.
  20. Slightly lift the RH 2nd row seat cushion pan upward, but do not fully remove the cushion at this time.
  21. Release the clips that attach the RH 2nd row seat floor latch actuator cable from the RH floor latch.
  22. Release the clips that attach the RH 2nd row seat floor latch actuator cable from the LH floor latch.
  23. Release the clips that attach the RH 2nd row seat easy entry actuator cable to the RH easy entry latch.
  24. Release the clips that attach the RH 2nd row seat easy entry actuator cable to the LH easy entry latch.
  25. Release the clips that attach the RH 2nd row seat recliner actuator cable to the recliner release arm.
  26. Remove the RH 2nd row seat cushion assembly from seat frame.
  27. Disconnect the RH 2nd row seat heat pad electrical connector.
  28. Release locking tab that attaches the RH 2nd row seat heater pad connector to the cushion pan.
  29. Disconnect the RH 2nd row seat occupancy sensor electrical connector.
  30. Release the holding tab that attaches the RH 2nd row seat occupancy sensor harness to the cushion pan.
  31. Release the hooks that attach the RH 2nd row seat cushion trim cover to the cushion pan, and then remove the trim cover from the cushion pan..
  32. Release the Velcro that attaches the RH 2nd row seat cushion trim to the foam pad until the front hog rings are visible.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the Velcro approximately 11 cm.
  33. Use diagonal cutters to cut the hog rings at the front of the RH 2nd row seat cushion trim, and then release the cover from the hog rings.
  34. Separate the remaining portion of the RH 2nd row seat cushion trim from the foam pad until the remaining hog rings are visible.
  35. Use diagonal cutters to cut the remaining hog rings, release the cover from the hog rings, and then remove the RH 2nd row seat cushion trim.

Install

  1. Position the RH 2nd row seat cushion trim onto the foam padding.
  2. Use hog ring pliers to crimp the hog rings to the RH 2nd row seat cushion trim at the rear of the foam padding.
  3. Attach an additional 21 cm of the remaining portion of the RH 2nd row seat cushion trim to the foam padding.
  4. Use hog ring pliers to crimp the hog rings to the RH 2nd row seat cushion trim at the front of the foam padding.
  5. Attach the remaining portion of the RH 2nd row seat cushion trim to the foam padding.
  6. Position the RH 2nd row seat cushion trim cover onto the cushion pan, and then fasten the hooks.
  7. Fasten the holding tab that attaches the RH 2nd row seat occupancy sensor harness to the cushion pan.
  8. Connect the RH 2nd row seat occupancy sensor electrical connector.
  9. Install the RH 2nd row seat heater pad connector to the cushion pan.
  10. Connect the RH 2nd row seat heat pad electrical connector.
  11. Position the RH 2nd row seat cushion assembly onto the seat from, but do not fully seat the cushion assembly.
  12. Fasten the clips that attach the RH 2nd row seat recliner actuator cable to the recliner release arm.
  13. Install the RH 2nd row seat easy entry actuator cable to the LH easy entry latch.
  14. Install the RH 2nd row seat easy entry actuator cable to the RH easy entry latch.
  15. Install the RH 2nd row seat floor latch actuator cable to the LH floor latch.
  16. Install the RH 2nd row seat floor latch actuator cable from the RH floor latch.
  17. Push downward on the RH 2nd row seat cushion assembly to fully seat it to the seat frame.
  18. Install the clip that attaches the RH 2nd row seat cushion pan to the seat frame.
  19. Install the bolts that attach the RH 2nd row seat cushion pan to the seat frame.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  20. Fasten the clips that attach the RH 2nd row seat cushion harness to the podium.
  21. Connect the RH 2nd row seat seat track position sensor electrical connector.
  22. Fasten the clip that attaches the RH 2nd row seat seatbelt buckle connector to the cushion pan.
  23. Connect the RH 2nd row seat seatbelt buckle electrical connector.
  24. Connect the RH 2nd row seat LH floor latch electrical connector.
  25. Connect the RH 2nd row seat RH floor latch electrical connector.
  26. Install the clip that attaches the RH 2nd row seat cushion harness connector to the seat frame.
  27. Connect the LH 2nd row seatback harness electrical connector.
  28. Fasten the hook that attaches the inner B-cover to the RH 2nd row seat assembly.
  29. Disconnect the RH 2nd row seat recliner actuator electrical connector.
  30. Using the seat fold tool, connect the recliner actuator electrical connector into the recliner actuator, and then activate the switch to fold the RH 2nd row seat down.
  31. Disconnect the seat fold tool from the RH 2nd row seat.
  32. Connect the RH 2nd row seat recliner actuator electrical connector.
  33. Position the RH 2nd row seat outer B-cover onto the inner B-cover, and then install the clips (x4).
  34. Connect the RH 2nd row seat side shield electrical connector.
  35. Position the RH 2nd row seat side shield onto the RH 2nd row seat assembly, and then install the clip.
  36. Install the clip that attaches the RH 2nd row seat side shield to the cushion pan.
  37. Install the RH 2nd row seat toe kick cover.
  38. Install the RH 2nd row seat assembly. See Seat Assembly - 2nd Row - RH (7-Seat) (Remove and Replace).