19/02/2021 13:23:49

Switch Box - Actuator - 2nd Row Seat - RH (7-Seat) (Remove and Replace)

Correction code 13050042 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Remove the RH 2nd row seat assembly. See Seat Assembly - 2nd Row - RH (7-Seat) (Remove and Replace).
  2. Remove the RH 2nd row seat toe kick cover.
  3. Remove the clip that attaches the RH 2nd row seat side shield to the cushion pan.
  4. Release the clip that attaches the RH 2nd row seat side shield to the RH 2nd row seat assembly, and then lift the shield up to release it from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not pull the shield away from the assembly as there is still an electrical connector connected
  5. Disconnect the RH 2nd row seat side shield electrical connector, and then remove the shield from the assembly.
  6. Release the clips (x4) that attach the RH 2nd row seat outer B-cover from the inner B-cover, and slide the cover towards the rear of the seat to remove it from the assembly.
  7. Fold the seat to the upright position.
  8. Remove the screw that attaches the RH 2nd row seat inner B-cover to the cushion pan.
    1.5 Nm (1.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
  9. Release the hook that attaches the inner B-cover to the RH 2nd row seat assembly.
  10. Release the clips that attach the RH 2nd row seat cushion harness to the podium.
  11. Remove the clip that attaches the RH 2nd row seat cushion pan to the seat frame.
  12. Slightly lift the RH 2nd row seat cushion pan upward, but do not fully remove the cushion at this time.
  13. Disconnect the RH 2nd row seat easy entry actuator electrical connector.
  14. Disconnect the RH 2nd row seat floor latch actuator electrical connector.
  15. Disconnect the RH 2nd row seat actuator switch box electrical connector.
  16. Remove the bolts that attach the RH 2nd row seat actuator switch box to the seat assembly, and then remove it from the assembly.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension

Install

  1. Position the RH 2nd row seat actuator switch box onto the seat assembly, and then install the bolts.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
  2. Connect the RH 2nd row seat actuator switch box electrical connector.
  3. Connect the RH 2nd row seat floor latch actuator electrical connector.
  4. Connect the RH 2nd row seat easy entry actuator electrical connector.
  5. Push downward on the RH 2nd row seat cushion to fully seat the cushion to the frame.
  6. Install the clip that attaches the RH 2nd row seat cushion pan to the seat frame.
  7. Fasten the clips that attach the RH 2nd row seat cushion harness to the podium.
  8. Fasten the hook that attaches the inner B-cover to the RH 2nd row seat assembly.
  9. Install the screw that attaches the RH 2nd row seat inner B-cover to the cushion pan.
    1.5 Nm (1.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
  10. Disconnect the RH 2nd row seat recliner actuator electrical connector.
  11. Using the seat fold tool, connect the recliner actuator electrical connector into the recliner actuator, and then activate the switch to fold the RH 2nd row seat down.
  12. Connect the RH 2nd row seat recliner actuator electrical connector.
  13. Disconnect the seat fold tool from the RH 2nd row seat.
  14. Position the RH 2nd row seat outer B-cover onto the inner B-cover, and then install the clips (x4).
  15. Connect the RH 2nd row seat side shield electrical connector.
  16. Position the RH 2nd row seat side shield onto the RH 2nd row seat assembly, and then install the clip.
  17. Install the clip that attaches the RH 2nd row seat side shield to the cushion pan.
  18. Install the RH 2nd row seat toe kick cover.
  19. Install the RH 2nd row seat assembly. See Seat Assembly - 2nd Row - RH (7-Seat) (Remove and Replace).