28/09/2024 23:08:25

A/C Line - Supermanifold to Compressor (Remove and Replace)

Correction code 18201902 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-09-29: Updated the UI routines and added note on adding correction code for refrigerant recovery/recharge 18200102 as a separate activity to the service visit.
  • 2023-06-12: Added "Thermal Performance" routine through touchscreen.
Informational PurposesAn informational icon, calling your attention
Note
This procedure requires the A/C Refrigerant (Recovery and Recharge) procedure to be performed. If not already automatically added to the Service Visit, add correction code 18200102 as a separate activity to the Service Visit.

Remove

  1. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  2. Remove the HEPA filter assembly. See Assembly - Filter - HEPA (Remove and Replace).
  3. Unlock the vehicle gateway. See Gateway (Unlock).
  4. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Thermal > Refrigerant System > Start Thermal Fill Drain (Refrigerant only) > Run, and allow the routine to complete.
  5. Recover the A/C refrigerant. See A/C Refrigerant (Recovery and Recharge).
  6. Remove the nut that attaches the supermanifold to compressor suction line to the compressor.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 13 mm deep socket
    • Flex head ratchet/flex head torque wrench
  7. Remove the nut that attaches the supermanifold to compressor discharge line to the compressor, and then move the line aside for clearance.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 13 mm deep socket
    • Flex head ratchet/flex head torque wrench
  8. Remove the bolt that attaches the supermanifold to compressor A/C line to the supermanifold, and then remove the assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
    • 6 in extension

Install

  1. Position the supermanifold to compressor A/C line onto the supermanifold, and then hand tighten the bolt that attaches the A/C line to the supermanifold.
  2. Tighten the bolt that attaches the supermanifold to compressor A/C line to the supermanifold.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
    • 6 in extension
  3. Install the nut that attaches the supermanifold to compressor discharge line to the compressor.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 13 mm deep socket
    • Flex head ratchet/flex head torque wrench
  4. Install the nut that attaches the supermanifold to compressor suction line to the compressor.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 13 mm deep socket
    • Flex head ratchet/flex head torque wrench
  5. Perform the vacuum leak test and refill A/C refrigerant. See A/C Refrigerant (Recovery and Recharge).
  6. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Thermal > Sensors and Valves > Run Heat Pump Commissioning > Run, and allow the routine to complete.
  7. Tap Actions > Test Thermal Performance, select Run, and allow the routine to complete.
  8. Tap Actions > Test HVAC Performance, select Run, and allow the routine to complete.
  9. Disable Service Mode. See Service Mode.
  10. Install the HEPA filter assembly. See Assembly - Filter - HEPA (Remove and Replace).
  11. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).