21/03/2024 12:30:44

Software Reinstall - Toolbox

Correction code 00020008 0.05 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2023-06-08: Updated Li-Ion instructions: Vehicle software version 2023.12 or newer is required, and consolidated "contactors closed" and "contactors open" procedures.
Informational PurposesAn informational icon, calling your attention
Note
This procedure describes how to reinstall the currently installed vehicle software using a laptop with Toolbox 3 locally connected. The package will not be downloaded from Tesla servers.
The software reinstall process varies depending on whether the vehicle is equipped with a lead acid or li-ion battery.

Firmware Redeploy (Lead Acid Battery)

  1. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  2. Connect a LV battery maintainer to make sure power is not lost during the software reinstall.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If using a 50A or 80A maintainer, make sure the maintainer is set to "Lead Acid" or "Half Power" mode. Failure to do so could damage the LV battery.
  3. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
    Informational PurposesAn informational icon, calling your attention
    Note
    Locally connecting the vehicle to Toolbox 3 will automatically enable Service Mode Plus.
  4. In Toolbox, select the Actions/Autodiag tab, and then search for "redeploy".
  5. Run the UPDATE_CAN-REDEPLOY routine and wait for the reinstallation to complete. Reinstallation status can be monitored on the vehicle touchscreen.
    Tip: UPDATE_CAN-REDEPLOY is a "partial" software reinstallation that reinstalls the currently installed software package to all module, ECU, and component replacements, with the exception of the car computer.
  6. Once the reinstallation is complete, check that the release notes appear on the touchscreen, indicating a successful reinstallation.
  7. Disconnect the LV battery maintainer.
  8. Disconnect the laptop from the vehicle. See Toolbox 3 (Connect and Disconnect).
  9. Disable Service Mode. See Service Mode.
  10. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).

Software Reinstall (Li-Ion Battery)

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Vehicle software version 2023.12 or newer is required in order to perform this procedure.
  1. Connect the LV maintainer to the vehicle, but do not disconnect the LV battery. See LV Maintainer (Connect and Disconnect).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is OK for the LV maintainer and LV battery to both be connected while performing this procedure.
  2. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
    Informational PurposesAn informational icon, calling your attention
    Note
    Locally connecting the vehicle to Toolbox 3 will automatically enable Service Mode Plus.
  3. In Toolbox, select the Actions/Autodiag tab, and then search for "redeploy".
  4. Run the UPDATE_CAN-REDEPLOY routine and wait for the reinstallation to complete. Reinstallation status can be monitored on the vehicle touchscreen.
    Tip: UPDATE_CAN-REDEPLOY is a "partial" software reinstallation that reinstalls the currently installed software package to all module, ECU, and component replacements, with the exception of the car computer.
  5. Once the reinstallation is complete, check that the release notes appear on the touchscreen, indicating a successful reinstallation.
  6. Disconnect the LV maintainer from the vehicle. See LV Maintainer (Connect and Disconnect).
  7. Disconnect the laptop from the vehicle. See Toolbox 3 (Connect and Disconnect).
  8. Disable Service Mode. See Service Mode.
  9. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).