29/05/2024 18:12:17

Actuator - Bleed - LH (Remove and Replace)

Correction code 18102212 2.25 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Remove the underhood storage unit. See Underhood Apron - Rear (Remove and Replace)
  2. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect)
  3. Remove the instrument panel carrier from the cross car beam. See IP Carrier (Remove and Install)
  4. Remove screws securing the drivers air duct to cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    2x scews, T20, 2.3 Nm
  5. Remove drivers air duct from the HVAC assembly
  6. Release the IP harness clip from the body of the vehicle by RH cross car beam bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x harness clip
  7. Release the IP harness clip from the cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x harness clip
  8. Release clip from RH side of cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x harness clip
  9. Release clip from body of vehicle on RH lower A-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x harness clip
  10. Release headliner harness clip from body of vehicle located on LH upper A-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x harness clip
  11. Release headliner harness clips located on LH lower A-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  12. Remove LH touchscreen bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T30, 12 Nm
  13. Remove RH touchscreen bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T30, 12 Nm
  14. Remove bleeder duct adapter from HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  15. Remove nuts securing upper steering column to cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 13mm, 15 Nm
  16. Remove nuts securing lower steering column to cross car beam and carefully lower steering column
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 13mm, 15 Nm
  17. Remove bolts securing cross car beam to LH side of bulkhead
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 13mm, 25 Nm
  18. Remove clip securing the carpet to LH cross car beam bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  19. Remove the bolt that secures the LH cross car beam bracket to the cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolts, 13mm, 25 Nm
  20. Remove nut securing the LH cross car beam bracket to the body and remove LH cross car beam bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 13mm, 25 Nm, Slightly pull LH carpet towards LH side of vehicle, Take note of direction of cross car beam bracket during removal
  21. Remove clip securing the carpet to RH cross car beam bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  22. Remove bolt securing RH cross car beam bracket to cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolts, 13mm, 25 Nm
  23. Remove nut securing the RH cross car beam bracket to body and remove the RH cross car beam bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 13mm, 25 Nm, Slightly pull the RH carpet towards RH side of vehicle, Take note of direction of cross car beam bracket during removal
  24. Remove bolts securing cross car beam to the HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts, 10mm, 5.5 Nm
  25. Remove bolt securing the cross car beam to HVAC assembly on upper LH side of HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt. 10mm, 5.5 Nm
  26. Remove bolt that secures the cross car beam to the upper cowl
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 13mm, 25 Nm
  27. Remove bolts securing cross car beam to LH side of body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 15mm, 29 Nm
  28. Remove bolts securing cross car beam to RH side of body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 15mm, 29 Nm
  29. Pull out and lift up left side of the cross car beam exposing left bleed actuator
  30. Disconnect LH bleed actuator connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  31. Remove bolts securing LH bleed actuator and remove bleed actuator from HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 6mm, 2.3 Nm
  32. Position LH bleed actuator to HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure it's in the right place
  33. Install bolts securing LH bleed actuator to HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 6mm, 2.3 Nm
  34. Connect LH bleed actuator connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  35. Position the cross car beam into the vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure accurate location
  36. Loosely install bolts securing cross car beam to RH side of body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 15mm, 29 Nm, Torque at later step
  37. Loosely install bolts securing cross car beam to LH side of body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 15mm, 29 Nm, Torque at later step
  38. Loosely install bolt securing cross car beam to upper cowl
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 13mm, 25 Nm
  39. Loosely install bolt securing cross car beam to the HVAC assembly on upper LH side of HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 5.5 Nm
  40. Loosely install bolts securing the cross car beam to HVAC assembly in front of the HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts, 10mm, 5.5 Nm
  41. Install RH cross car beam bracket and loosely install nut that secures the RH cross car beam bracket to body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 13mm, 25 Nm
  42. Loosely install bolt securing RH cross car beam bracket to the cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolts, 13mm, 25 Nm
  43. Install LH cross car beam bracket and loosely install nut that secures LH cross beam bracket to body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 13mm, 25 Nm
  44. Loosely install bolt to secure LH cross car beam bracket to cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolts, 13mm, 25 Nm
  45. Install bolts securing cross car beam to LH side of bulkhead
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 13mm, 25 Nm
  46. Torque the bolt that secures the LH cross car beam bracket to the cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolts, 13mm, 25 Nm
  47. Torque nut securing LH cross car beam bracket to body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 13mm, 25 Nm,Slightly pull LH carpet towards LH side of vehicle
  48. Install clip that secures the carpet to LH cross car beam bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  49. Torque bolt securing the RH cross car beam bracket to cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 13mm, 25 Nm
  50. Torque nut securing RH cross car beam bracket to body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 13mm, 25 Nm
  51. Install clip securing the carpet to RH cross car beam bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  52. Torque the bolts securing the cross car beam to the HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts, 10mm, 5.5 Nm
  53. Torque the bolt that secures the cross car beam to the HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 5.5 Nm
  54. Torque the bolt that secures the cross car beam to the upper cowl
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 13mm, 25 Nm
  55. Torque bolts securing cross car beam to LH side of body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 15mm, 29 Nm
  56. Torque bolts securing cross car beam to RH side of body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 15mm, 29 Nm
  57. Install the nuts securing the lower steering column to the cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 13mm, 15 Nm
  58. Install nuts securing upper steering column to cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 13mm, 15 Nm
  59. Install the bleeder duct adapter to the HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  60. Install RH touchscreen bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T30, 12 Nm
  61. Install LH touchscreen bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T30, 12 Nm
  62. Install the headliner harness clip located on the LH upper A pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  63. Install headliner harness clips to LH lower A-Pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  64. Install clip located on the RH lower A-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  65. Install the clip located on the RH side of cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  66. Install the IP harness clip to the cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  67. Install IP harness clip to the body of the vehicle next to RH cross car beam bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  68. Install the drivers air duct to the HVAC assembly
  69. Install the screws securing the drivers air duct to the cross car beam
    Informational PurposesAn informational icon, calling your attention
    Note
    2x scews, T20, 2.3 Nm
  70. Install the instrument panel carrier onto the cross car beam. See IP Carrier (Remove and Install)
  71. Connect 12V power. See 12V/LV Power (Disconnect and Connect)
  72. Connect to vehicle using Toolbox 3.0
  73. Select ‘Actions/Autodiag’ and search for ‘HVAC’
  74. Select ‘TEST-SELF_VCRIGHT_X_HVAC-PERFORMANCESearch for routine in ToolboxThermal / Actions - Test HVAC PerformanceThermal / Actions - Test HVAC Performance’, click ‘Run’, and allow routine to complete
    Informational PurposesAn informational icon, calling your attention
    Note
    Select ‘X’ at top right of window to close once complete
  75. Remove HSD cable from Ethernet port to disconnect Toolbox 3.0 from vehicle
  76. Install the underhood storage unit. See Underhood Apron - Rear (Remove and Replace)