26/09/2024 09:06:57

Seat Assembly - 1st Row - LH (Structural Pack) (Retrofit)

Correction code 13040106 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-09-26: Removed unneeded step for OCS self calibration Toolbox routine.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.
Informational PurposesAn informational icon, calling your attention
Note
Perform this procedure when installing a Non-Structural Pack seat in a Structural Pack vehicle. The Non-Structural Pack seat harness is 100mm shorter. Note the required harness slack during installation.
Informational PurposesAn informational icon, calling your attention
Note
The front seats contain airbags and pretensioners and therefore must be disposed of properly. See Remove the Front Seat Airbag and Discard for more information. Add Correction Code 20010707 to document the labor; the labor time for destructively removing and disposing of the front seat airbag and pretensioner is not reflected in the front seat removal and replacement labor time.
Informational PurposesAn informational icon, calling your attention
Note
Though the 1st row LH seat is described, the procedure is the same for the 1st row RH seat. This procedure can be used for the driver seat and the passenger seat in LHD and RHD vehicles.
  • 1133787-00-A Key, Seat Belt Release, Model 3
  • 1082447-07-A Torx Plus T45

Install

  1. With assistance, position the 1st row LH seat in the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take care not to damage the upholstery or trim while positioning the seat.
  2. Install the LH front seat harness connector on the LH body controller, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform a push-pull test to ensure that the connector is fully seated and locked.
  3. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  4. Install the clips (x2) that attach the LH front seat harness to the LH footwell support bracket near the LH side of the LH footwell.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use new zip ties.
  5. Route the 1st row LH seat harness under the LH front carpet, position the harness in the harness guide, and then install the clips that attach the harness to the harness guide.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use zip ties and tape to install the clips to the harness and into position.
  6. Tilt the LH front seat backwards, and let it rest against the 2nd row seat cushion.
  7. Secure the LH front seat harness to the clips (x2) under the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Leave 290mm of slack in the harness between the splice and the first clip.
  8. Unfold the LH front carpet back into position, and then install the clip that attaches the carpet to the body near the front of the LH door opening.
  9. Tilt the LH front seat down, and place the seat into position for installation.
  10. Move the LH front seat fully rearward.
  11. Install the new bolts (x2) that attach the front of the 1st row LH seat to the body.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • 3/8 in std flex head ratchet
    • 3/8 in flex head torque wrench (installation only)
  12. Install the seat track front covers. See Cover - Front - Seat Track - 1st Row Seat (Remove and Replace).
  13. Move the LH front seat fully forward.
  14. Install the LH front seatbelt retractor onto the pretensioner.
    Informational PurposesAn informational icon, calling your attention
    Note
    After reinstalling the seatbelt pretensioner into the seatbelt pretensioner coupling, perform a pull test to make sure that the seatbelt and pretensioner are securely engaged.
  15. Install the new bolts (x2) that attach the rear of the 1st row LH seat to the body.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • 3/8 in std flex head ratchet
    • 3/8 in flex head torque wrench (installation only)
  16. Install the seat track rear covers. See Cover - Rear - Seat Track - 1st Row Seat (Remove and Replace).
  17. Install the LH lower A-Pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  18. Install the LH mid A-Pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  19. If servicing the driver seat:
    1. Use the vehicle touchscreen to place the vehicle into Service Mode. See Service Mode.
    2. Reinstall the vehicle software. See Software Reinstall - Touchscreen.
    3. On the vehicle touchscreen, touch Controls > Service > Driver Seat, Steering & Mirrors Calibration > Start.
    4. Exit Service Mode. See Service Mode.
  20. If servicing the front passenger seat in a North American vehicle:
    1. Consult the parts catalog to see if a configuration change is needed.
    2. Reinstall the vehicle software. See Software Reinstall - Touchscreen.
    3. Remove all objects from the front passenger seat before beginning calibration.
    4. Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
    5. Unlock the vehicle gateway. See Gateway (Unlock).
    6. In Toolbox, click on the Actions tab, and then search for "Seat calibration".
    7. Run the PROC_VCRIGHT_SEAT-CALIBRATESearch for routine in Toolbox routine.
    8. Disconnect Toolbox and remove the laptop from the vehicle.
  21. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  22. Move the seat to its original position.
  23. Raise all the windows and close all the doors.