07/09/2023 08:04:16

Roof Rack (Install)

Correction code 12400001 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2023-08-16: Added steps that apply to Model Y.
  • 2023-09-05: Updated the measurements provided for locating the arrows on the glass.

Install

  1. Clean the roof rack installation locations with isopropyl alcohol (IPA) wipes, and allow to dry for 1 minute before continuing.
  2. Install the anti-abrasion tape on the front LH side of the vehicle:
    1. Measure 227 mm back from the front edge of the glass roof to locate the arrow on the glass.
      Warning IconA warning icon, calling your attention to a possibly risky situation
      CAUTION
      The measurement for the front and rear crossbar locations are different.
    2. Align the arrow on the glass with the arrow on the anti-abrasion tape, then apply the anti-abrasion tape to the vehicle so that it follows the trim line.
  3. Perform the previous step on the front RH side of the vehicle.
  4. Install the anti-abrasion tape on the rear LH side of the vehicle:
    1. Measure 412 mm forward from the rear edge of the glass roof to locate the arrow on the glass.
    2. Align the arrow on the glass with the arrow on the anti-abrasion tape, then apply the anti-abrasion tape to the vehicle so that it follows the trim line.
  5. Perform the previous step on the rear RH side of the vehicle.
  6. Install the roof rack rail clips and pads on all corners of the vehicle:
    1. Use the supplied trim tool to carefully lift the seal at the arrow location then insert a rail clip so that it is aligned with the arrow on the anti-abrasion tape.
    2. Ensure that the rail clip is properly secured to the J-hook under the roof glass then remove the trim tool. Make sure the clip is centered on the arrow.
    3. Using the icon on the pad to identify which corner of the vehicle it goes to, place the appropriate pad over the rail clip so that the clip and threads are exposed.
  7. With an assistance, place the front and rear crossbars onto the front and rear pads so that the threads on the clips are exposed in the opening of the ends of the crossbars.
    Informational PurposesAn informational icon, calling your attention
    Note
    The front crossbar is longer than the rear crossbar. Ensure the clip studs are vertical before mounting.
  8. Hand tighten the wingnuts onto the clips on all four corners of the vehicle; do not torque a wingnut until the wingnut on the other side of the vehicle is already hand tightened.
  9. Torque all wingnuts to their proper specification. Ensure the marking on the wingnuts align with the markings on the crossbars (the notch faces outboard) to lock the crossbars using the provided keys.
    3.5 Nm (2.6 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    To avoid damaging the roof glass, do not overtorque the fasteners, and alternately tighten the both sides evenly.
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • ¼ in to 3/8 in adapter
    • 8 mm socket
  10. Use the provided keys to lock (rotate clockwise on LH side locks, rotate counter-clockwise on RH side locks) both crossbars in place.
  11. Push and pull on both crossbars to ensure that they are fully secured and locked in place.
  12. Starting from the bottom and working up, install the roof rack side cover on each side of both crossbars.
    Informational PurposesAn informational icon, calling your attention
    Note
    The bottom of the side covers have guiding tabs that insert into the crossbar.
  13. Ensure the customer receives the locking key(s) when they take delivery of the vehicle.