14/08/2024 23:58:39

Cover - Seat Back - 2nd Row - RH (7-Seat) (Remove and Replace)

Correction code 13081022 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-08-15: Added a note for NA vehicles to remind that the seat covers without ISOFIX flag for child locks must be replaced.

Remove

  1. Remove the RH 2nd row back panel. See Back Panel – 2nd Row Seat – RH (Remove and Replace).
  2. Remove the RH 2nd row seat shoulder switch. See Shoulder Switch – Seat Back – 2nd Row – LH (Remove and Replace).
  3. Remove the RH 2nd row seat toe kick cover. See Cover - Toe Kick - 2nd Row Seat - RH (7-Seat) (Remove and Replace).
  4. Remove the clips (x2) and elastic harness holder that attach the seat harness to the bottom side of the seat frame, and then disconnect the 2nd row seat connector.
  5. Remove the RH 2nd row headrest. See Headrest - 2nd Row - Outer - LH (Remove and Replace).
  6. Remove the RH 2nd row headrest adjustment guide and guide lock. See:
  7. Release the clips (x4) that attach the RH 2nd row seat back assembly to the vehicle, and then lift the seat back upward to remove it from the vehicle.
  8. Place the RH 2nd row seat back assembly on a suitable working surface.
  9. Disconnect the seat heating connector.
  10. Release the tabs (x16) that attach the RH 2nd row seat back cover to the seat back assembly.
  11. Remove the back rest shell from the RH 2nd row seat back cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    Early production vehicles may have staples holding the material to the shell in some areas.
  12. Release the hook and loop attachment around the perimeter, cut and discard the hog rings (x3), and then remove the RH 2nd row seat back cover from the foam.
    Informational PurposesAn informational icon, calling your attention
    Note
    Clean any remaining debris from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    For NA only: The seat cover without ISOFIX flag for child locks must be replaced.

Install

  1. Position the RH 2nd row seat back cover onto the foam, and then install the hog rings (x3) and secure the hook and loop around the perimeter.
    Informational PurposesAn informational icon, calling your attention
    Note
    Small cable ties may be used as a substitute for the hog rings. If cable ties are used, trim the excess cable flush, and then rotate the head away from the visible areas.
  2. Position the seat back shell into the RH 2nd row seat back cover, and then secure the tabs (x16) that attach the cover to the seat back shell.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the cover is evenly distributed on the front of the back rest.
  3. Connect the seat heating connector.
  4. Position the RH 2nd row seat back cover into the vehicle, and then install the seat back assembly into the seat assembly.
  5. Install the RH 2nd row headrest adjustment guide and guide lock. See:
  6. Install the RH 2nd row headrest. See Headrest - 2nd Row - Outer - LH (Remove and Replace).
  7. Connect the 2nd row seat harness connector, and then secure the clips (x2) and elastic harness holder that attach the seat harness to the bottom side of the seat frame.
  8. Install the RH 2nd row seat toe kick cover. See Cover - Toe Kick - 2nd Row Seat - RH (7-Seat) (Remove and Replace).
  9. Install the RH 2nd row seat should switch. See Shoulder Switch – Seat Back – 2nd Row – LH (Remove and Replace).
  10. Install the RH 2nd row back panel. See Back Panel – 2nd Row Seat – RH (Remove and Replace).