2021-03-12

Actuator - Floor Latch - 2nd Row Seat - LH (7-Seat) (Remove and Replace)

Correction code 13020052 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure. See Ergonomic Precautions for safe and healthy working practices.

Remove

  1. Remove the LH 2nd row seat assembly. See Seat Assembly - 2nd Row - LH (7-Seat) (Remove and Replace).
  2. With assistance, place the LH 2nd row seat assembly on a stable work area.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Prevent the seat assembly from tipping over. Fold the center armrest down to stabilize the weight. Use a ballast bag and ay additional support as needed.
  3. Remove the LH 2nd row seat toe kick cover. See Cover - Toe Kick - 2nd Row Seat - LH (7-Seat) (Remove and Replace).
  4. Remove the bolts that attach the LH 2nd row seat rear cushion pan to the seat frame.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  5. Remove the clip that attaches the LH 2nd row seat side shield to the seat assembly.
  6. Lift the LH 2nd row seat side shield up and away from the seat assembly to release it.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not pull the side shield away from the seat assembly as there is still an electrical connector connected.
  7. Disconnect the LH 2nd row seat side shield electrical connector, and then remove the side shield from the assembly.
  8. Gently pull the seat cushion trim aside to reveal the cushion pan fastener, and then remove the fastener.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
  9. Release the clips that attach the LH 2nd row seat inboard outer cover from the inboard inner assembly, and then remove the cover from the assembly.
  10. Release hook that attaches the LH 2nd row seat strap to the inboard inner assembly.
  11. Remove the LH 2nd row seat inboard inner assembly screw.
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Flex head ratchet/flex head torque wrench
  12. Place the LH 2nd row seat on its back.
  13. Remove the LH 2nd row seat seat cushion pan clips.
  14. Lift up on the LH 2nd row seat cushion assembly, but do not remove it.
  15. Release the LH 2nd row seat floor latch cable from the outboard floor latch.
  16. Release the LH 2nd row seat floor latch cable from the inboard floor latch.
  17. Disconnect the LH 2nd row seat floor latch actuator electrical connector.
  18. Remove the screws that attach the LH 2nd row seat floor latch actuator to the cushion pan, and then remove the actuator from the assembly.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
    • Flex head ratchet/flex head torque wrench

Install

  1. Install the LH 2nd row seat floor latch actuator to the cushion pan, and then install the screws.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
    • Flex head ratchet/flex head torque wrench
  2. Connect the LH 2nd row seat floor latch actuator electrical connector.
  3. Install the LH 2nd row seat floor latch cable onto the outboard floor latch.
  4. Install the LH 2nd row seat floor latch cable onto the inboard floor latch.
  5. Lower the LH 2nd row seat cushion assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the cables and wiring harness are not pinched between the seat cushion assembly and seat frame.
  6. Install the LH 2nd row seat seat cushion pan clips.
  7. Install the LH 2nd row seat inboard inner assembly screw.
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Flex head ratchet/flex head torque wrench
  8. Hook the LH 2nd row seat strap to the inboard inner assembly.
  9. Install the LH 2nd row seat inboard outer cover onto the inboard inner assembly.
  10. Gently pull the seat cushion trim aside to reveal the cushion pan fastener location, and then install the fastener.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
  11. Position the LH 2nd row seat side shield onto the seat assembly, and then connect the electrical connector.
  12. Lift up on the LH 2nd row seat side shield, and then hook the side shield onto the seat cushion assembly.
  13. Install the clip that attaches the LH 2nd row seat side shield to the seat assembly.
  14. Install the bolts that attach the LH 2nd row seat rear cushion pan to the seat frame.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  15. Disconnect the LH 2nd row seat recliner actuator electrical connector.
  16. Using the seat fold tool, connect the recliner actuator electrical connector into the recliner actuator, and then activate the switch to fold the LH 2nd row seat down.
  17. Disconnect the seat fold tool from the LH 2nd row seat.
  18. Connect the LH 2nd row seat recliner actuator electrical connector.
  19. Install the LH 2nd row seat toe kick cover. See Cover - Toe Kick - 2nd Row Seat - LH (7-Seat) (Remove and Replace).
  20. Install the LH 2nd row seat assembly. See Seat Assembly - 2nd Row - LH (7-Seat) (Remove and Replace).