24/05/2023 02:20:37

Glass - Door - LH - Rear (Remove and Replace)

Correction code 11500302 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1135305-00-A Tool, Window Switch Bypass, Model 3
  • 1129348-00-A XP-10 Power Supply, XP-10
  • 2023-05-24: Added cleaning instructions to prevent glass damage.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The side impact airbag deployment depends on the rear door sensor's ability to detect a side impact from air pressure. Make sure that there are no uncovered holes in the rear door shells. Additionally, always reinstall plugs or tape when servicing or inspecting the rear doors and their components.

Torque Specifications

Table 1. Torque Specifications: Glass - Door - LH - Rear (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the LH rear door glass to the regulator guide blocks
12 Nm (8.8 lbs-ft)
  • 10 mm socket
  • Flex head ratchet/flex head torque wrench
  • 2 in extension
Reuse

Remove

  1. Remove the rear LH door trim panel. See Panel - Door Trim - Rear - LH (Remove and Install).
  2. Remove the LH rear door inner belt seal. See Seal - Inner Belt - Rear Door - LH (Remove and Replace).
  3. Remove the plugs that cover the opening in the door for access to the regulator guide block bolts.
  4. Temporarily connect the puddle light to the LH rear door harness.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Route the electrical cable so that it will not be damaged when closing the door.
  5. Connect the window switch special tool to the LH rear door harness.
  6. Latch the LH rear door to allow the window to raise fully, and then raise the window for access to the regulator guide blocks.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not close the door with the window in this position, as upper bright trim will be damaged.
  7. Remove the bolts that attach the door glass to the regulator guide blocks, and then remove the door glass from the door.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • Flex head ratchet/flex head torque wrench
    • 2 in extension
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace the regulator isolator clamps, if damaged.

Install

  1. Inspect the regulator guide blocks for glass splinters or other debris, and clean them if necessary.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Debris and splinters may damage or shatter the new door glass.
  2. Position the door glass into the rear door.
  3. Install and hand-tighten the bolts that attach the door glass to the regulator guide blocks.
    12 Nm (8.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the guide blocks are not bottomed out on the regulator.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • Flex head ratchet/flex head torque wrench
    • 2 in extension
  4. Lower the window fully.
  5. Install the inner belt seal . See Seal - Inner Belt - Rear Door - LH (Remove and Replace).
  6. Adjust the door glass. See Glass - Door - LH - Rear (Adjust).
  7. Install the rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Install).
  8. Calibrate the windows. See Window Regulator (Recalibrate).