24/08/2023 22:27:40

Switch - Interior Door Release - Rear - LH (Remove and Replace)

Correction code 15131802 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2023-08-25: Add a step for inserting the inflatable air bag for eailer removal of the switch weld points.

Remove

  1. Open the LH rear door and lower the LH rear window.
  2. Remove the LH rear door puddle light. See Puddle Light - Rear Door - LH (Remove and Replace).
  3. Remove the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Install).
  4. Release the tabs (x4), and then remove the NVH pad from the LH rear door trim panel.
  5. Gently pry on the door trim panel to remove the bolt that attaches the interior door release handle switch to the door trim panel.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  6. Separate the pins (x3) from the electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Separate the pins and plug to ensure that they can pass through the narrow trim panel space.
    Informational PurposesAn informational icon, calling your attention
    Note
    Mark the position of pins and the electrical connector.
  7. Apply masking tape around the work area to protect the door trim panel.
  8. Pry open the front portion of interior door handle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure there is enough space to remove the interior door release switch.
  9. Carefully insert the inflatable air bag between the LH door trim panel and the door handle to form a gap.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to damage any interior components.
  10. Use the cordless rotary to remove the switch weld points if necessary.
    Informational PurposesAn informational icon, calling your attention
    Note
    This is only for vehicles built by Shanghai factory.
  11. Release the tabs (x2), and then remove the interior door release switch from the door trim panel.

Install

  1. Separate the pins (x3) from the electrical connector of new interior door release switch.
    Informational PurposesAn informational icon, calling your attention
    Note
    Separate the pins and plug to ensure that they can pass through the narrow trim panel space.
    Informational PurposesAn informational icon, calling your attention
    Note
    Mark the position of pins and the electrical connector.
  2. Fasten the tabs (x2) that attach the interior door release switch onto the door trim panel.
  3. Secure the pins to the electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Mark the position of pins and the electrical connector.
  4. Secure the front portion of the interior door handle onto the door trim panel.
  5. Remove the masking tape from the door trim panel.
  6. Gently pry on the door trim panel to install the bolt that attaches the interior door release handle to the door trim panel.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  7. Install the NVH pad onto the rear door trim panel and secure the pad with the tabs (x4).
  8. Install the LH rear door puddle light. See Puddle Light - Rear Door - LH (Remove and Replace).
  9. Install the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Install).