Torque Specifications - Chassis
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Rear subframe insert that threads into the rear underbody casting. |
|
|
Reuse |
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Small bolts that attach the LH shear plate to the HV battery (non-Structural Pack) |
|
|
Reuse | |
Small bolts that attach the LH shear plate to the HV battery (Structural Pack) |
|
|
||
Large bolt that attaches the LH shear plate and rear subframe to the body |
|
|
Replace |
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Bolts that attach the LH rear brake caliper bracket to the knuckle |
|
|
Replace | |
Bolts that attach the LH rear damper at the top mount |
|
|
Reuse | |
Nut that attaches the rear drive unit ground strap to the body |
|
|
Reuse | |
Nuts that attach the HV battery to rear drive unit harness bracket to the HV battery |
|
|
Reuse | |
Small bolts that attach the LH shear plate to the HV battery (non-Structural Pack vehcles) |
|
|
Reuse | |
Small bolts that attach the LH shear plate to the HV battery (Structural Pack vehicles) |
|
|
||
Large bolt that attaches the LH shear plate and rear subframe to the body |
|
|
Replace | |
Bolts that attach the rear subframe to the body |
|
|
Replace |
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Bolt that attaches the rear of the rear drive unit to the rear subframe |
|
|
Reuse | |
Bolt that attaches the LH mount of the rear drive unit to the rear subframe |
|
|
Reuse | |
Bolt that attaches the RH mount of the rear drive unit to the rear subframe |
|
|
Reuse | |
Bolt and nut that attaches the RH rear upper aft link to the subfame |
|
|
Reuse | |
Bolt and nut that attaches the RH rear upper fore link to the subfame |
|
|
Reuse | |
Bolt and nut that attaches the RH rear toe link to the subfame |
|
|
Reuse | |
Bolt and nut that attaches the RH rear lower fore link to the subfame |
|
|
Reuse | |
Bolt that attaches the HV harness bracket to the inverter |
|
|
Reuse | |
Smaller bolts that attach the LH and RH shear plates to the vehicle (non-Structural Pack vehicles) |
|
Tip:
Use of the following
tool(s) is recommended:
|
Reuse | |
Smaller bolts that attach the LH shear plate to the HV battery (Structural Pack vehicles) |
|
|
||
Large bolts that attach the LH and RH shear plates to the vehicle |
|
|
replace | |
Bolts that attach the LH and RH rear subframe to the body |
|
|
replace | |
Nut that attaches the HV battery to rear drive unit harness bracket to the HV battery |
|
|
Reuse | |
Nut that attaches the rear drive unit ground strap to the body |
|
|
Reuse | |
Bolts that attach the LH rear damper at the top mount |
|
|
Reuse | |
Bolts that attach the LH rear brake caliper bracket to the knuckle |
|
|
Replace | |
Bolt that attaches the rear LH ABS wheel speed sensor to the knuckle |
|
|
Reuse | |
Bolt that attaches the LH front rotor to the LH front hub |
|
|
Reuse | |
Bolt and nut that attach the LH rear upper aft link to the knuckle |
|
|
Reuse |
Note The bolt and nut
will be tightened to specification during the Four Wheel Alignment
(Check and Adjust) at the end of the Front Subframe Assembly (Remove
and Install) procedure. |
Bolt and nut that attach the LH rear upper fore link to the knuckle |
|
|
Reuse |
Note The bolt and nut
will be tightened to specification during the Four Wheel Alignment
(Check and Adjust) at the end of the Front Subframe Assembly (Remove
and Install) procedure. |
Bolt and nut that attach the RH rear upper fore link to the knuckle |
|
|
Reuse | |
Bolt and nut that attach the LH rear toe link to the knuckle |
|
|
Reuse |
Note The bolt and nut
will be tightened to specification during the Four Wheel Alignment
(Check and Adjust) at the end of the Front Subframe Assembly (Remove
and Install) procedure. |
Bolt and nut that attaches the LH rear lower fore link to the knuckle |
|
|
Reuse |
Note The bolt and nut
will be tightened to specification during the Four Wheel Alignment
(Check and Adjust) at the end of the Front Subframe Assembly (Remove
and Install) procedure. |
Bolt and nut that attaches the LH rear lower aft link to the knuckle |
|
|
Reuse |
Note The bolt and nut
will be tightened to specification during the Four Wheel Alignment
(Check and Adjust) at the end of the Front Subframe Assembly (Remove
and Install) procedure. |
Bolt and nut that attach the LH rear damper assembly to the LH rear lower aft link |
|
|
Reuse | |
Bolt and nut that attaches the LH rear lower fore link to the subfame |
|
|
||
Bolt and nut that attaches the LH rear upper aft link to the subfame |
|
|
||
Bolt and nut that attaches the LH rear upper fore link to the subfame |
|
|
||
Bolt and nut that attaches the LH rear toe link to the subfame |
|
|
||
Nut that attaches the end link to the stabilizer bar |
|
|
||
LH front drive unit halfshaft nut |
|
|
Replace |