Track - Outer - Front Passenger Seat (Remove and Replace)
Correction code 13013002 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure. NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.
Remove
- Check that the firmware is version 2023.2.11 or above. If the firmware version is not 2023.2.11 or above, update the vehicle firmware.
- Remove the front passenger seat from the vehicle. See Seat Assembly - 1st Row - LH (Remove and Replace).
- Remove the front passenger seat outboard side shield. See Side Shield - Outboard - Driver Seat (Remove and Replace).
- Remove the front passenger seat outboard lap pretensioner. See Pretensioner - Outboard Lap - 1st Row - LH (Remove and Replace).
-
Release the pretensioner harness clips
(x3) from the seat assembly.
-
Lay the seat on its seat back to gain
access to the underside of the seat cushion.
CAUTIONProtect the seat cushion from damage as necessary.
- Remove the RH 1st row seat track position sensor. See Sensor - Position - Track - 1st Row Seat - RH (Remove and Replace).
-
Disconnect the height motor electrical
connector.
-
Release the clip that attaches the
track motor harness to the track motor housing.
-
Disconnect track motor electrical
connector.
-
Remove and discard the bolt that
attaches the height motor assembly to the seat cushion frame.Tip: Use of the following tool(s) is recommended:
- Torx T50 socket
-
Remove and discard the bolt that
attaches the height motor assembly to the rear RH link.Tip: Use of the following tool(s) is recommended:
- Torx T45 socket
-
Slide the lift motor assembly downward
and then outward, away from the wiring harness, to remove it from the seat
assembly.
-
Remove and discard the bolts that
attach the front passenger seat outer track to the seat assembly.Tip: Use of the following tool(s) is recommended:
- Torx T50 socket
-
Release front passenger seat outer
track from the track bridge assembly.
NotePry up on bridge tack motor tab, and then slide the outer track away to release it.
-
Install the front passenger seat outer
track onto the track bridge assembly.
NoteTrack motor cable is keyed square and must be aligned with outer track. Turn the cable by hand to align as needed. Slide the track motor bridge into the outer track until fully seated.
Install
-
Install new bolts that attach the front passenger seat outer track to the seat
assembly.Tip: Use of the following tool(s) is recommended:
- Torx T50 socket
-
Install the clip that attaches the track motor harness to the track motor
housing.
-
Connect track motor electrical connector.
-
Position the height motor assembly to
the seat cushion frame for installation.
NoteInstall the motor assembly at an angle to ensure the under seat harnesses are clear.
-
Install a new bolt that attaches the height motor assembly to the rear RH link.Tip: Use of the following tool(s) is recommended:
- Torx T45 socket
-
Install a new bolt that attaches the height motor assembly to the seat cushion
frame.Tip: Use of the following tool(s) is recommended:
- Torx T50 socket
-
Connect the height motor electrical connector.
- Install the RH 1st row seat track position sensor. See Sensor - Position - Track - 1st Row Seat - RH (Remove and Replace).
- Return the seat to normal upright position
- Install the front passenger seat outboard lap pretensioner. See Pretensioner - Outboard Lap - 1st Row - LH (Remove and Replace).
-
Install seat belt pretensioner harness
clips (x3).
- Install the front passenger seat outboard side shield. See Side Shield - Outboard - Driver Seat (Remove and Replace).
- Install the front passenger seat into the vehicle. See Seat Assembly - 1st Row - LH (Remove and Replace).
-
If servicing the front passenger seat in
a North American vehicle:
- Remove all objects from the front passenger seat before beginning calibration.
- On the vehicle touchscreen, touch Software Reinstall - Touchscreen. If the vehicle firmware is not 2023.2.11 or newer, update the vehicle firmware. See Software Update. and check the vehicle firmware version. If the vehicle firmware is 2023.2.11 or newer, perform a software reinstall. See
- Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
- Unlock the vehicle gateway. See Gateway (Unlock).
- In Toolbox, click on the Actions tab, and then search for "OCS".
- Run the PROC_OCS1P_SELF-CALIBRATIONSearch for routine in ToolboxOCS1P delete Sandwich and calibrate routineSafety & Restraints / Seats - OCS1P Self Capacitance Calibration routine.
- Click on the Actions tab, and then search for "Seat calibration".
- Run the PROC_VCRIGHT_SEAT-CALIBRATESearch for routine in ToolboxRight Seat Calibration routine.
- Disconnect Toolbox and remove the laptop from the vehicle.