Torque Specifications - Rear Drive Unit
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Bolt that attaches the rear drive unit HV harness bracket to the rear drive unit |
![]() 6 Nm (4.4 lbs-ft) |
|
Reuse | |
Bolt that attaches the rear LH ABS wheel speed sensor to the knuckle |
![]() 5 Nm (3.7 lbs-ft) |
|
Reuse | |
Bolt that attaches the ground strap harness to the rear drive unit assembly |
![]() 10 Nm (7.4 lbs-ft) |
|
Reuse | |
Bolt and nut that attach the LH rear upper aft link to the knuckle |
![]() 134 Nm (98.8 lbs-ft) |
|
Reuse |
Note The bolt and nut
will be tightened to specification during the Four Wheel Alignment
(Check and Adjust) at the end of the Rear Subframe Assembly (Remove
and Install) procedure. |
Bolt and nut that attach the LH upper fore link to the knuckle |
![]() 84 Nm (61.9 lbs-ft) |
|
Reuse |
Note The bolt and nut
will be tightened to specification during the Four Wheel Alignment
(Check and Adjust) at the end of the Rear Subframe Assembly (Remove
and Install) procedure. |
Bolt and nut that attach the LH rear toe link to the knuckle |
![]() 76 Nm (56.0 lbs-ft) |
|
Reuse |
Note The bolt and nut
will be tightened to specification during the Four Wheel Alignment
(Check and Adjust) at the end of the Rear Subframe Assembly (Remove
and Install) procedure. |
Nut that attaches the LH rear lower aft link to the knuckle |
![]() 115 Nm (84.8 lbs-ft) |
|
Reuse |
Note The bolt and nut
will be tightened to specification during the Four Wheel Alignment
(Check and Adjust) at the end of the Rear Subframe Assembly (Remove
and Install) procedure. |
Nut that attaches the LH rear lower fore link to the knuckle |
![]() 76 Nm (56.0 lbs-ft) |
|
Reuse |
Note The bolt and nut
will be tightened to specification during the Four Wheel Alignment
(Check and Adjust) at the end of the Rear Subframe Assembly (Remove
and Install) procedure. |
Bolt that attaches the LH mount of the rear drive unit to the rear subframe |
![]() 80 Nm (59.0 lbs-ft) |
|
Reuse | |
Bolt that attaches the RH mount of the rear drive unit to the rear subframe |
![]() 80 Nm (59.0 lbs-ft) |
|
Reuse | |
Bolt that attaches the rear of the rear drive unit to the rear subframe |
![]() 80 Nm (59.0 lbs-ft) |
|
Reuse |
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Nut that attaches the rear drive unit ground strap to the body |
![]() 10 Nm (7.4 lbs-ft) |
|
Reuse | |
Bolt that secures the rear drive unit HV cable bracket to the drive unit |
![]() 6 Nm (4.4 lbs-ft) |
|
Reuse | |
Nut that secures the rear drive unit HV cable bracket to the HV battery |
![]() 10 Nm (7.4 lbs-ft) |
|
Reuse | |
Bolts that attach the rear subframe to the body |
![]() 165 Nm (121.7 lbs-ft) |
|
Reuse | |
LH mount bolt that secures the drive unit to subframe |
![]() 80 Nm (59.0 lbs-ft) |
|
Reuse | |
Bolts on the rear drive unit LH mount assembly |
![]() 35 Nm (25.8 lbs-ft) and 55 degrees |
|
Reuse | |
Bolt that secures the outlet fitting to manifold |
![]() 6 Nm (4.4 lbs-ft) |
|
Replace |
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Bolt that attaches the HV harness bracket to the inverter |
![]() 6 Nm (4.4 lbs-ft) |
|
Reuse | |
Bolts (x2) that attach the 3-phase access cover to the rear drive unit |
![]() 14 Nm (10.3 lbs-ft) |
|
Reuse | |
Bolts (x3) that attach the 3-phase terminals rear drive unit |
![]() 11.5 Nm (8.5 lbs-ft) |
|
Replace | |
Bolts (x12) that attach the inverter to the gearbox assembly |
![]() 12.5 Nm (9.2 lbs-ft) |
|
Reuse |
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Bolt that secures the 55 degrees fluid coupling |
![]() 6 Nm (4.4 lbs-ft) |
|
Replace |
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|