08/11/2024 05:57:57

Module - Cooling Fan (Remove and Replace)

Correction code 18201312 1.32 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: GUID-81F39FBB-029E-4729-9A82-C8F42F8879FC.html
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the underhood storage unit reinforcement bracket to the cooling fan
48 Nm (35.4 lbs-ft)
  • External Torx Plus EP14
  • Flex head ratchet/flex head torque wrench
  • 3 in extension
Reuse
Bolts that attach the lower LH and RH of the cooling fan module to the ankle catcher
10 Nm (7.4 lbs-ft)
  • 8 mm socket
  • Flex head ratchet/flex head torque wrench
  • 4 in extension
Reuse

Install

  1. With assistance, position the cooling fan module assembly into the vehicle, and then loosely install the bolts that attach the module assembly to the vehicle.
  2. Torque the bolts that attach the LH and RH of the cooling fan module to the vehicle.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Assistance is recommended to support the assembly.
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
    Figure 1. LH Side
    Figure 2. RH Side
  3. Remove the plugs from the radiator outlet hose, connect the male and female fittings, and then fasten the hose clip.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform a push-pull-push test on the fittings to make sure that they are secure.
  4. Remove the plugs from the radiator inlet hose, connect the male and female fittings, and then fasten the hose clip.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform a push-pull-push test on the fittings to make sure that they are secure.
  5. Connect the electrical harness from the cooling fan module connector, and then engage the connector lock.
  6. Install the front valance. See Valance - Front Fascia (Remove and Replace).
  7. Install the front aero shield panel. See Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
  8. Lower the vehicle until the tires touch the ground.
  9. Position the underhood storage unit reinforcement bracket onto the cooling fan, and then install the bolts that attach the bracket to the fan.
    48 Nm (35.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • External Torx Plus EP14
    • Flex head ratchet/flex head torque wrench
    • 3 in extension
  10. Connect the ambient temperature sensor electrical connector, and then install the sensor cover onto the active grille shutter.
  11. Connect the active grille shutter electrical connector, and then engage the connector lock.
  12. Perform a coolant system vacuum refill. See Cooling System (Vacuum Refill).
  13. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  14. Perform the following routine using Service Mode or Toolbox (see 0005 - Service Modes): TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCESearch for routine in ToolboxThermal System Performance TestDrive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System TestDrive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System TestDrive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System TestDrive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System TestDrive Unit ➜ Front Drive Unit Replacement ➜ Thermal System TestDrive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System TestThermal ➜ Actions ➜ Test Thermal Performance
    Informational PurposesAn informational icon, calling your attention
    Note
    Select the "X" at the top right of the window to close once the routine is complete.
  15. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  16. Close the LH front door and raise the LH front window.