30/04/2021 09:05:19

B-Cover - Inner - 3rd Row - LH (Remove and Replace)

Correction code 13090012 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Open all the doors and fully lower all the windows.
  2. Open the liftgate.
  3. Move the front seats fully forward.
  4. Move the 2nd row seat into easy entry mode.
  5. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  6. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  7. Remove the 3rd row seat cushion. See Cushion - Seat - 3rd Row (Remove and Replace).
  8. Disconnect the 3rd row seat frame harness electrical connector.
  9. Remove the rear load floor. See Trunk Load Floor - Rear (Remove and Replace).
  10. Remove the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  11. Release the clips and tabs that attach the LH trunk bracket to the vehicle, and then remove the trim. Repeat this step for the RH trunk bracket.
    Figure 1. LH shown; RH similar
  12. Remove the trunk tub carpet from the vehicle. See Tub - Rear Trunk (Remove and Replace).
  13. Remove the LH 3rd row seat back panel. See Back Panel - 3rd Row Seat - LH (Remove and Replace).
  14. Remove the LH 3rd row seat headrest closeout. See Headrest Closeout - 3rd Row Seat - LH (Remove and Replace).
  15. Remove the LH 3rd row seat shoulder switch. Shoulder Switch – Seat Back – 3rd Row – LH (Remove and Replace).
  16. Release the clips (x2) that attach the LH 3rd row escutcheon to the seat assembly, and then remove the trim from the assembly.
  17. Remove the bolts that attach the 3rd row LH backrest to the LH seat back assembly.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • 4 in extension
  18. Release the clips that attach the 3rd row LH backrest to the LH seat back assembly.
    Tip: Push the clips in with pliers while applying outward pressure to the backrest.
  19. Remove the 3rd row LH backrest from the seat back assembly.
  20. Remove the RH 3rd row seat cushion bolster. See Bolster - Seat Cushion - 3rd Row - LH (Remove and Replace).
  21. Remove and discard the bolt that attaches the 3rd row RH seat belt retractor to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
    • Flex head ratchet/flex head torque wrench
    Figure 2. LH shown; RH similar
  22. Remove the LH 3rd row seat cushion bolster. See Bolster - Seat Cushion - 3rd Row - LH (Remove and Replace).
  23. Remove the bolt that attaches the 3rd row LH seat belt retractor to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
    • Flex head ratchet/flex head torque wrench
  24. Remove and discard the outer bolts that attach the 3rd row seat back assembly to the body.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
  25. Remove and discard the inner bolts that attach the LH 3rd row seat back assembly to the vehicle.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
  26. Remove the 3rd row seat back assembly from the vehicle.
  27. Release the clips that attach the LH 3rd row seat outer B-cover to the inner B-cover.
  28. Remove the clips that attach the LH 3rd row seat inner B-cover to the seat assembly, and then remove the trim from the assembly.

Install

  1. Position the LH 3rd row seat inner B-cover onto the seat assembly, and then install the clips that attach the cover to the assembly.
  2. Fasten the clips that attach the LH 3rd row seat outer B-cover to the inner B-cover.
  3. Install the 3rd row seat back assembly into the vehicle.
  4. Install and hand tighten new inner bolts that attach the LH 3rd row seat back assembly to the vehicle.
  5. Install and hand tighten new outer bolts that attach the LH 3rd row seat back assembly to the vehicle.
  6. Install and hand tighten a new bolt that attaches the 3rd row RH seat belt retractor to the seat frame assembly.
  7. Install the bolt that attaches the 3rd row LH seat belt retractor to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
    • Flex head ratchet/flex head torque wrench
  8. Torque the bolt that attaches the 3rd row RH seat belt retractor to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
    • Flex head ratchet/flex head torque wrench
  9. Torque the outer bolts that attach the 3rd row seat back assembly to the body.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
  10. Torque the inner bolts that attach the LH 3rd row seat back assembly to the vehicle.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
  11. Position the 3rd row LH backrest onto the seat back assembly, and then install the clips and fasten the tabs.
  12. Install the bolts that attach the 3rd row LH backrest to the LH seat back assembly.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • 4 in extension
  13. Install the RH 3rd row escutcheon onto the seat assembly.
    Figure 3. LH shown; RH similar
  14. Install the LH 3rd row seat shoulder switch. Shoulder Switch – Seat Back – 3rd Row – LH (Remove and Replace).
  15. Install the LH 3rd row headrest seat closeout panel. See Headrest Closeout - 3rd Row Seat - LH (Remove and Replace).
  16. Install the LH 3rd row seat back panel. See Back Panel - 3rd Row Seat - LH (Remove and Replace).
  17. Install the trunk tub carpet. See Tub - Rear Trunk (Remove and Replace).
  18. Position the LH trunk bracket into the vehicle, and then seat the clips and tabs. Repeat this step for the RH trunk bracket.
    Figure 4. LH shown; RH similar
  19. Install the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  20. Install the rear load floor. See Trunk Load Floor - Rear (Remove and Replace).
  21. Install the LH and RH 3rd row seat cushion bolsters. See Bolster - Seat Cushion - 3rd Row - LH (Remove and Replace).
  22. Connect the 3rd row seat frame harness electrical connector.
  23. Install the 3rd seat cushion. See Cushion - Seat - 3rd Row (Remove and Replace).
  24. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  25. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  26. Move the 2nd row seats and front seat into the original positions.
  27. Raise all the windows and close all the doors.
  28. Close the liftgate.