04/03/2021 09:46:24

Retractor - Seatbelt - 3rd Row - LH (Remove and Replace)

Correction code 20058102 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Open all the doors and fully lower all the windows.
  2. Open the liftgate.
  3. Move the front seats fully forward.
  4. Move the 2nd row seats into easy entry mode.
  5. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  6. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  7. Remove the 3rd row seat cushion. See Cushion - Seat - 3rd Row (Remove and Replace).
  8. Remove the 3rd row LH seat cushion bolster. See Bolster - Seat Cushion - 3rd Row - LH (Remove and Replace).
  9. Remove and discard the bolt that attaches the 3rd row LH seat belt retractor to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
    • Flex head ratchet/flex head torque wrench
    • 3 mm hex
  10. Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  11. Remove the LH 3rd row seat back panel. See Back Panel - 3rd Row Seat - LH (Remove and Replace).
  12. Remove the 3rd row LH headrest closeout panel. See Headrest Closeout - 3rd Row Seat - LH (Remove and Replace).
  13. Remove the LH 3rd row seat back shoulder switch. See Shoulder Switch – Seat Back – 3rd Row – LH (Remove and Replace).
  14. Remove the LH 3rd row seat escutcheon. See Escutcheon - Seat Belt - 3rd Row - LH (Remove and Replace).
  15. Remove the fasteners that attach the LH 3rd row seat back rest to the LH seat back assembly.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
  16. Release the clips that attach the LH 3rd row seat back rest to the LH seat back assembly, and then remove the back rest from the vehicle.
    Tip: Push the clips in with pliers while applying outward pressure to the back rest.
  17. Remove and discard the bolt that attaches the LH 3rd row seatbelt retractor to the LH seat back assembly. and then rempove the retractor from the vehicle.
    45 Nm (33.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T50 socket
    • Flex head ratchet/flex head torque wrench

Install

  1. Install a new bolt that attaches the LH 3rd row seatbelt retractor to the LH seat back assembly.
    45 Nm (33.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T50 socket
    • Flex head ratchet/flex head torque wrench
  2. Install the LH 3rd row seat back rest onto the LH seat back assembly.
  3. Install the fasteners that attach the LH 3rd row seat back rest to the LH seat back assembly.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
  4. Install the LH 3rd row seat escutcheon. See Escutcheon - Seat Belt - 3rd Row - LH (Remove and Replace).
  5. Install the LH 3rd row seat back shoulder switch. See Shoulder Switch – Seat Back – 3rd Row – LH (Remove and Replace).
  6. Install the 3rd row LH headrest closeout panel. See Headrest Closeout - 3rd Row Seat - LH (Remove and Replace).
  7. Install the LH 3rd row seat back panel. See Back Panel - 3rd Row Seat - LH (Remove and Replace).
  8. Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  9. Install a new bolt that attaches the 3rd row LH seat belt retractor to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
    • Flex head ratchet/flex head torque wrench
    • 3 mm hex
  10. Install the 3rd row LH seat cushion bolster. See Bolster - Seat Cushion - 3rd Row - LH (Remove and Replace).
  11. Install the 3rd row seat cushion. See Cushion - Seat - 3rd Row (Remove and Replace).
  12. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  13. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  14. Move the 2nd row seats to the original position.
  15. Move the front seats to the original position.
  16. Close the liftgate.
  17. Raise all the windows and close all the doors.
  18. Close the liftgate.