Headlights - Adjust - NA (Tool Method)
Correction code 17400150 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.
Identify Headlight Type
Adjust Headlights Using a Headlight Tester
Special tools required for this procedure:
Supplier | Part Number | Description |
Tesla | 1133367-00-A | Beissbarth Headlight Tester, Model 815 |
- Park the vehicle on a level surface.
- Make sure that all 4 tires are inflated to specification.
- Open the front trunk hood.
- Remove the rear underhood apron.Underhood Apron - Rear (Remove and Replace)
- On the vehicle touchscreen, enter headlight adjustment mode: Controls > Service > Adjust Headlights.
- Turn on the headlights.
- Position the headlight tester tool ~11 in. (30 cm) from the front of the LH headlight lens.
- Adjust the height of the headlight tester tool to ~30.5 in. (80 cm) above the ground to align with the center point of the headlamp.
- Connect the headlight tester tool to an electrical outlet, and then turn on the headlight tester tool.
-
Adjust the knobs on the base of the headlight tester tool until the tool is leveled, as indicated by the bubble gauge on the tool.
NoteThe bubble must be entirely inside of the center ring in order to properly align the headlights.
-
Turn on the alignment laser near the top of the tool, and then rotate the tool as necessary to align the laser with the rearmost fender bolts.
- On the headlight tester tool, select Test US, then select Applications >Free Test.
- On the headlight tester tool, select Headlight, and then use the + or - buttons to change the Headlight type to "VOR".
- On the headlight tester tool, select Light, and then use the + or - buttons to change the Light type to Bi-LED.
- Select "OK", and then "OK" again to proceed past the fog light settings.
-
On the headlight tester tool, select Height.
- On the headlight tester tool, select Laser, and then position the laser in the middle of the headlight.
- Move the headlight tester tool up or down on the column to the indicated height.
- On the headlight tester tool, select OK.
- On the headlight tester tool, select Laser to turn on the headlight laser guide.
-
On the headlight tester tool, select Left low beam, and then select Low beam near the bottom of the screen.
NoteThe "L" and "R" indicators at the bottom of the screen are reversed. For example, "L" is on the right side and "R" is on the left side.
-
Adjust the headlight laser guide crosshair to line up with the vertical and horizontal marks on the LH headlight.
NoteOr place a piece of paper against the LH headlight, and then adjust the tool to place the headlight laser guide crosshair over the brightest spot on the paper.
- On the headlight tester tool, select Laser to turn off the headlight laser guide.
-
On the steering wheel, use the left scroll wheel to adjust the beam level: Target 0.00" +/- 1.0"
CAUTIONDo not sit in the vehicle, as this will affect headlight alignment.NoteThere might be a delay between the scroll wheel input and actual headlight adjustment output.
- On the headlight tester tool, select Save to record the results.
- Roll the headlight tester tool to the RH headlight, and then position the tool ~30 cm from the front of the RH headlight lens.
-
On the headlight tester tool, select Right low beam, and then select Low beam near the bottom of the screen.
NoteMake sure that High beam is not selected.NoteThe "L" and "R" indicators at the bottom of the screen are reversed. For example, "L" is on the right side and "R" is on the left side.
- Adjust the headlight laser guide crosshair to line up with the vertical and horizontal marks on the RH headlight.
- On the headlight tester tool, select Laser to turn off the headlight laser guide.
-
On the steering wheel, use the right scroll wheel on the steering wheel to adjust the beam level: Target 0.00" +/- 1.0"
CAUTIONDo not sit in the vehicle while using the scroll wheel as this will affect headlight alignment.NoteThere might be a delay between the scroll wheel input and actual headlight adjustment output.
- On the headlight tester tool, select Save to record the results.
- On the headlight tester tool, select Save again to view test results.
- Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
- Close the front trunk hood.
- On the touchscreen, select the "x" in the top left corner of the window..