Headlights - Adjust - Global (Tool Method)
Correction code 17400170 0.15 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.
- 2024-06-12: Updated procedure to latest validation.
Special tools required for this procedure:
Supplier | Part Number | Description |
Tesla | 1133367-00-A | Beissbarth Headlight Tester, Model 815 |
Identify Headlight Type
Adjust Global Headlights Using a Headlight Tester
- Open the driver's door and lower the window.
-
Enter headlight adjustment mode:
- Park the vehicle on a level surface.
- Make sure that all 4 tires are inflated to specification.
- Open the front trunk.
- Remove the rear underhood apron.Underhood Apron - Rear (Remove and Replace)
- Position 75 kg of ballast in the driver's seat.
- Turn on the headlights.
- Position the headlight tester tool approximately 30 cm (~ 12 in) from the front of the LH headlight lens.
- Adjust the height of the headlight tester tool to 81 cm (~30.5 in) above the ground to align with the center axis of the headlight.
-
Adjust the knobs on the base
of the headlight tester tool until the tool is leveled, as indicated by the
bubble gauge on the tool.
NoteThe bubble must be entirely inside of the center ring in order to properly align the headlights.
- Turn on the headlight tester tool.
-
Turn on the alignment laser
near the top of the tool, and then rotate the tool as necessary to align the
laser with the rearmost fender bolts.
- Regardless of the region, select on the headlight tester tool.
- On the headlight tester tool, select Vehicle, and then use the + or - buttons to set the vehicle type to Tesla Y.
-
On the headlight tester
tool, select Headlight, use the + or
-
buttons to set the Headlight type to EU Asym, and
then use the small - button next to the EU Asym field
to select TMR.
- On the headlight tester tool, select Light, and then use the + or - buttons to set the Light type to Bi-LED.
-
On the headlight tester
tool, select Inclinat., and then use the + or
-
buttons to set the inclination to 0.0 %.
NoteDuring headlight adjustment in headlight adjustment mode, the inclination is set to 0.0 %. When the vehicle is not in headlight adjustment mode and the headlights are turned on, the inclination is automatically adjusted to the required region specific value.
- On the headlight tester tool, select Height, and then use the + or - buttons to set the height to 81 cm.
- Press OK, and then OK again to skip the fog light settings.
- On the headlight tester tool, press the "laser beam" button to turn on the headlight laser guide.
- Adjust the headlight laser guide crosshair horizontally and vertically to to line up with the markings on the headlight.
- On the headlight tester tool, press the "laser beam" button to turn off the headlight laser guide.
- If not already activated, enter headlight adjustment mode. On the vehicle touchscreen, touch: Controls > Service > Adjust Headlights.
-
On the headlight tester
tool, press the LH TMR button on the left side of the
screen, and then press the TMR button at the bottom
of the screen.
NoteThe "L" and "R" indicators at the bottom of the screen are reversed: "L" is on the right side and "R" is on the left side.
- On the vehicle touchscreen, touch Left.
-
On the steering wheel, use
the left scroll wheel to adjust the beam. When adjusted to within
specification, the color of the beam indicator on the headlight tester tool
will change from red to green.
NoteThe vehicle must be loaded with approximately 75 kg in the driver's seat during headlight alignment.NoteThere might be a delay between the scroll wheel input and the actual headlight adjustment output.
- On the headlight tester tool, press the "Save" button to record the results for the LH headlight.
- Move the headlight tester tool to the RH headlight, position the tool ~30 cm (~ 11 in) from the front of the RH headlight lens.
- Align the tool to the RH headlight (see steps 21 to 23).
-
On the headlight tester
tool, press the RH TMR button on the right side of
the screen, and then press the TMR button at the
bottom of the screen.
NoteThe "L" and "R" indicators at the bottom of the screen are reversed: "L" is on the right side and "R" is on the left side.
- On the vehicle touchscreen, touch Right.
-
On the steering wheel, use
the left scroll wheel to adjust the beam level. When adjusted to within
specification, the color of the beam indicator on the headlight tester tool
will change from red to green.
NoteThe vehicle must be loaded with approximately 75 kg in the driver's seat during headlight alignment.NoteThere might be a delay between the scroll wheel input and actual headlight adjustment output.
- On the headlight tester tool, press the "Save" button to record the results for the RH headlight, and then press "Save" again to view the results for both headlights.
- Press the "Print" button to print out the results, if desired.
- Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
- Close the front trunk.
- On the touchscreen, exit the headlight adjustment mode.