04/09/2024 15:21:28

Spoiler - Rear (Remove and Replace)

Correction code 12220402 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Figure 1. Model 3 shown; Model Y similar
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  • 1567345-00-A MY Spoiler Jig or
  • 1680404-E0-A Spoiler Jig, Model Y, EMEA
  • 1453028-00-A KIT, BADGE REMOVAL

Remove

  1. Use a towel and/or compressed air to clean the area surrounding the spoiler.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    To avoid personal injury, eye protection must be worn while using compressed air.
  2. Assemble the badge removal kit by cutting an approximately 24 inch section of fishing line and connecting each end of the fishing line to a handle using a knot.
  3. Starting from one end of the spoiler, carefully use the badge removal kit to release the spoiler from the trunk.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Care must be taken to avoid damage to paintwork and exterior trim.
  4. Use a vacuum to remove any debris or dirt from the trunk.
  5. Using a rubber wheel, remove any remaining adhesive from the trunk.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    To avoid personal injury, eye and ear protection must be worn while performing this step.

Install (Non-EU type spoiler)

The below procedure applies to the installation of the Non-EU type spoiler. For installation of the EU type spoiler, see Install (EU type spoiler).

  1. Clean the spoiler installation surface with isopropyl alcohol (IPA) wipes, and allow it to dry before continuing.
    Informational PurposesAn informational icon, calling your attention
    Note
    Clean any moisture or contaminates that might be present from rain or vehicle washing, otherwise this might result in poor adhesion of the rear spoiler.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the trunk surface requires any paint correction, request assistance from the body shop or shop detailer before the installation of the rear spoiler.
    Informational PurposesAn informational icon, calling your attention
    Note
    It is recommended to perform this procedure indoors. Acceptable ambient and part temperature for installation is 15-43 degrees Celsius (60-110 degrees Fahrenheit) for proper adhesion.
  2. Install the base of the spoiler jig onto the trunk lid so that the cutout aligns with the Tesla "T" emblem.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    The base of the spoiler jig is held in place using magnets; take care not to damage the paint.
  3. Remove the label from the underside of the spoiler to expose the guide hole for the spoiler jig.
  4. Install the spoiler jig onto the rear spoiler so that the guide hole on the spoiler is centered between the notches in the spoiler jig.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take care not to damage the topside of the spoiler.
  5. Install the alignment jig so that the bottom tab is inserted into the guide hole on the spoiler and the side tabs are inserted into the notches on the spoiler jig.
    Informational PurposesAn informational icon, calling your attention
    Note
    The alignment jig is used to make sure the spoiler jig is completely centered on the spoiler prior to installation.
  6. Secure the spoiler jig to the top of the spoiler using masking tape.
  7. Remove the alignment jig from the spoiler jig.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to allow the spoiler jig to move out of position.
  8. Remove the adhesive backing from the bottom of the rear spoiler.
  9. Install the rear spoiler onto the trunk lid by aligning the guide pins on the bottom of the spoiler jig to the slots in the base of the spoiler jig. While performing this step, carefully hold both corners of the rear spoiler away from the trunk lid in order to install the center section of the rear spoiler first.
  10. Remove the spoiler jig and tape from the rear spoiler. Remove the base of the spoiler jig from the trunk lid.
  11. Starting at the center of the rear spoiler, firmly push downward and forwards towards the front of the vehicle. Continue this working outwards towards the ends of the spoiler to completely wet out the adhesive on the bottom of the rear spoiler.
  12. Perform a configuration update if necessary.

Install (EU type spoiler)

  • 1680404-E1-A SPOILER JIG, MODEL Y, EMEA
  1. Open the liftgate an put a kneeling pad on the liftgate striker, and then move the liftgate down as far as possible.
    Informational PurposesAn informational icon, calling your attention
    Note
    The kneeling pad will keep the liftgate slightly opened, facilitating the fitting of the LH and RH corner jigs later on.
  2. Clean the spoiler installation surface with isopropyl alcohol (IPA) wipes, and allow it to dry before continuing.
    Informational PurposesAn informational icon, calling your attention
    Note
    Clean any moisture or contaminates that might be present from rain or vehicle washing, otherwise this might result in poor adhesion of the rear spoiler.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the liftgate surface requires any paint correction, request assistance from the bodyshop or shop detailer before installation of the rear spoiler.
    Informational PurposesAn informational icon, calling your attention
    Note
    It is recommended to perform this procedure indoors. Acceptable ambient and part temperature for installation is 15-43 degrees Celsius (60-110 degrees Fahrenheit) for proper adhesion.
  3. Position the RH corner jig on the RH corner of the liftgate so that the protruding edge of the jig aligns with the edge of the liftgate panel, and then clamp the jig with a hold down tool to keep the jig in position.
    Figure 2. RH side shown, LH side similar
  4. Repeat the previous step on the LH side of the liftgate for the LH corner jig.
  5. Position the center jig by matching the cutout shape to the T-badge. The jig should contact the T-badge on both the top of the arch and the RH side of the T-leg.
  6. Clamp the center jig with a hold down tool to keep the jig in position.
  7. Remove the adhesive backing from the rear spoiler.
  8. Carefully position the rear spoiler above the liftgate so that the LH and RH sides of the rear spoiler coincide with the openings in the side jigs and the top center part of the rear spoiler is aligned with the top of the center jig.
  9. Attach each end of the rear spoiler to the liftgate.
  10. Remove the kneeling pad from the liftgate striker, and then close the liftgate.
  11. Using a pressure roller, perform the wet out of the adhesive: Starting at the center, firmly push downward and in towards the front of the vehicle, and then continue outwards towards both ends of the spoiler.
  12. Remove the spoiler alignment jigs from the vehicle.