30/09/2024 17:24:13

Motor - Seat Track - Front Passenger Seat (Remove and Replace)

Correction code 13013202 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2023-12-08: Re-write the whole procedure according to the latest validation.
Table 1. Torque Specifications: Motor - Seat Track - Front Passenger Seat (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Front passenger seat fasteners (x4)
33.5 Nm (24.7 lbs-ft)
  • Torx Plus T45 socket
  • Cordless Ratchet/Impact Driver
  • Flex head ratchet/flex head torque wrench
Replace Bolts are patched
Bolt that attaches the lift motor assembly to the rear RH link
18 Nm (13.3 lbs-ft)
  • Torx Bit T45 Stubby
  • Ratchet/torque wrench
  • 3 in extension
  • Flex head ratchet/flex head torque wrench
  • Cordless Ratchet/Impact Driver
Replace Bolts are patched
Bolts (x2) that attach the RH side track assembly to the RH front seat cushion assembly
23 Nm (17.0 lbs-ft)
  • Torx T50 Bit Stubby
  • 3 in extension
  • Flex head ratchet/flex head torque wrench
  • Cordless Ratchet/Impact Driver
Reuse Bolts are patched
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Remove

  1. Open all doors and lower all windows.
  2. Remove the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  3. Remove the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  4. Release the bottom half of the RH front door seal.
  5. Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  6. Use a clip prytool to release the RH front seat harness from the lower A-pillar 12V bracket clips (x5).
  7. Pull the RH front seat harness from under the RH front cabin carpet.
  8. Move the RH front seat forward, and then remove and discard the RH front seat rear fasteners (x2).
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  9. Raise the RH front seat cushion to maximum height for access to the HV battery bolts at the RH front footwell and below the RH front seat.
  10. Move the RH front seat backward, and then remove and discard the RH front seat front fasteners (x2).
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  11. Tilt the seat backward to gain access to the underside of the LH front seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care when moving the seat. Ensure the carpet is not damaged.
  12. Remove and discard the bolt that attaches the lift motor assembly to the rear RH link.
    Tip: Use of the following tool(s) is recommended:
    • Torx Bit T45 Stubby
    • Ratchet/torque wrench
    • 3 in extension
    • Flex head ratchet/flex head torque wrench
    • Cordless Ratchet/Impact Driver
  13. With assistance, remove the bolts (x2) that attach the RH side track assembly to the RH front seat cushion assembly.
    Tip: Use of the following tool(s) is recommended:
    • Torx T50 Bit Stubby
    • 3 in extension
    • Flex head ratchet/flex head torque wrench
    • Cordless Ratchet/Impact Driver
  14. Disconnect the front passenger seat track motor electrical connector.
  15. Use a clip prytool to remove the harness clips (x2) from the RH front seat track motor.
  16. Release the front passenger seat outer track from the track bridge assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pry up on the bridge tack motor tab, and then slide the outer track away to release it.
  17. Release the RH front seat track bridge assembly from the inner seat track.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pry up on the bridge tack motor tab, and then slide the seat track bridge assembly away to release it.

Install

  1. Install the RH front seat outer track onto the track bridge assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    The track motor cable is keyed square and must be aligned with the inner track. Turn the cable by hand to align as needed. Slide the track motor bridge into the inboard track till it is fully and securely seated.
  2. Install the track motor bridge to the inner track.
    Informational PurposesAn informational icon, calling your attention
    Note
    The track motor cable is keyed square and must be aligned with the inboard track. Turn the cable by hand to align as needed. Slide the track motor bridge into the inboard track till it is fully and securely seated.
  3. Connect the track motor electrical connector.
  4. Install the harness clips (x2) to the RH front seat track motor.
  5. With assistance, install the bolts (x2) that attach the RH side track assembly to the RH front seat cushion assembly.
    23 Nm (17.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T50 Bit Stubby
    • 3 in extension
    • Flex head ratchet/flex head torque wrench
    • Cordless Ratchet/Impact Driver
  6. Install a new bolt that attaches the lift motor assembly to the rear RH link.
    18 Nm (13.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Bit T45 Stubby
    • Ratchet/torque wrench
    • 3 in extension
    • Flex head ratchet/flex head torque wrench
    • Cordless Ratchet/Impact Driver
  7. Reposition the RH front seat onto the RH front seat risers.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care when moving the seat. Ensure the carpet is not damaged.
  8. Secure the RH front seat harness under the RH front cabin carpet.
  9. Install the RH front seat harness to the lower A-pillar 12V bracket clips (x5).
  10. Move the RH front seat forward, and then install new RH front seat rear fasteners (x2).
    33.5 Nm (24.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  11. Move the RH front seat backward, and then install new RH front seat front fasteners (x2).
    33.5 Nm (24.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  12. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  13. Install the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  14. Install the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  15. Install the RH front door seal along the lower A-pillar trim.
  16. Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  17. For NA vehicles only: On the laptop, select the Actions tab, then search for "OCS". Select PROC_OCS1P_SELF-CALIBRATIONSearch for routine in ToolboxSafety & Restraints / Seats - OCS1P Self Capacitance Calibration, click Run, and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify the seat is clear from any tooling or objects prior to calibration. Select ‘X’ at top right of the window to close once the routine is complete.
  18. On the laptop, select the Actions tab, then search for "Seat calibration". Select Search for routine in Toolbox, click Run, and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Select ‘X’ at top right of the window to close once the routine is complete.
  19. Disconnect Toolbox and remove the laptop from the vehicle.
  20. Disable Service Mode. See Service Mode.
  21. Move the RH front seat to original position.
  22. Raise all windows and close all doors.