19/02/2021 13:46:47

Substrate - Seat Back - 3rd Row - LH (Remove and Replace)

Correction code 13090032 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Open all the doors and fully lower all the windows.
  2. Open the liftgate.
  3. Move the front seats fully forward.
  4. Move the 2nd row seats into easy entry mode.
  5. Remove the 3rd row seat cushion. See Cushion - Seat - 3rd Row (Remove and Replace).
  6. Remove the bolt that attaches the 3rd row LH seat cushion bolster to the vehicle, and then slide the bolster forward to remove it from the assembly.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
  7. Remove the bolt that attaches the 3rd row LH seat belt retractor to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
    • Flex head ratchet/flex head torque wrench
  8. Remove the LH 3rd row seat back panel. See Back Panel - 3rd Row Seat - LH (Remove and Replace).
  9. Remove the LH 3rd row headrest closeout panel. See Headrest Closeout - 3rd Row Seat - LH (Remove and Replace).
  10. Remove the LH 3rd row shoulder switch. See Shoulder Switch – Seat Back – 3rd Row – LH (Remove and Replace).
  11. Remove the LH 3rd row escutcheon. See Shoulder Switch – Seat Back – 3rd Row – LH (Remove and Replace).
  12. Remove the bolts that attach the 3rd row LH backrest to the LH seat back assembly.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • 4 in extension
  13. Release the clips that attach the 3rd row LH backrest to the LH seat back assembly.
    Tip: Push the clips in with pliers while applying outward pressure to the backrest.
  14. Remove the 3rd row LH backrest from the seat back assembly.
  15. Release the tabs (x26) that attach the 3rd row LH trim cover to the LH back substrate.

Install

  1. Install the 3rd row LH trim cover onto the LH back substrate.
  2. Position the 3rd row LH backrest onto the seat back assembly, and then install the clips and fasten the tabs.
  3. Install the bolts that attach the 3rd row LH backrest to the LH seat back assembly.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • 4 in extension
  4. Install the LH 3rd row escutcheon. See Shoulder Switch – Seat Back – 3rd Row – LH (Remove and Replace).
  5. Install the LH 3rd row shoulder switch. See Shoulder Switch – Seat Back – 3rd Row – LH (Remove and Replace).
  6. Install the LH 3rd row headrest closeout panel. See Headrest Closeout - 3rd Row Seat - LH (Remove and Replace).
  7. Install the LH 3rd row seat back panel. See Back Panel - 3rd Row Seat - LH (Remove and Replace).
  8. Install the bolt that attaches the 3rd row LH seat belt retractor to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
    • Flex head ratchet/flex head torque wrench
  9. Position the 3rd row LH seat cushion bolster into the vehicle, and then install the bolt.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
  10. Install the 3rd row seat cushion. See Cushion - Seat - 3rd Row (Remove and Replace).
  11. Move the 2nd row seats and front seat into the original positions.
  12. Raise all the windows and close all the doors.
  13. Close the liftgate.