09/09/2022 09:02:01

Subframe Assembly - Front (RWD) (Remove and Install)

Correction code 30010301 1.86 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning

This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Raise and support vehicle

Note
Ensure vehicle is not charging before lifting it off the ground, Set air suspension to "Jack Mode" if equipped
Open LH front door
Lower LH front window
Set steering wheel straight ahead
Lock steering wheel into position

Note
Protect seat from damage
Open hood
Remove rear apron

Note
14x clips
Remove access panel

Note
3x clips, 1x connector
Remove fasteners securing the frunk assembly

Note
5x bolts, 10mm, 5 Nm, Newer vehicles may be equipped with 1x push clip securing frunk to reservoir neck
Remove frunk assembly from vehicle

Note
6x clips, Replace any clips if broken or missing
Remove bolt securing the steering gear assembly to intermediate shaft assembly

Note
1x bolt, 13mm, 18 Nm
Slide the electric steering column upward to remove it from the steering gear assembly
Power off vehicle from center display

Note
Via Controls > Safety & Security > Vehicle Power > Power Off
Disconnect 12V negative terminal and first responders loop

Note
1x nut, 10mm, 6 Nm, 1x connector, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V, Negative terminal should be disconnected before FRL, Allow 2 minutes for all electrical circuits to fully discharge
Disconnect the steering gear assembly connectors

Note
2x connectors, Two stage connectors, Slide red locking tab to unlock, then depress the connector release to disconnect
Disconnect logic connectors from steering gear assembly

Note
2x locking connectors, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector
Remove LH front wheel cap

Note
1x cap, Use both hands to gently pull the wheel cap to release the clips, Wheels may be equipped with center caps
Remove RH front wheel cap

Note
1x cap, Use both hands to gently pull the wheel cap to release the clips, Wheels may be equipped with center caps
Loosen RH front wheel

Note
5x nuts, 21mm, 175 Nm
Loosen LH front wheel

Note
5x nuts, 21mm, 175 Nm
Raise vehicle partially and lower lift onto locks

Note
Set vehicle to a comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
Remove LH front wheel

Note
5x nuts, 21mm, 175 Nm
Remove nut securing the LH tie rod end to the knuckle

Note
1x nyloc nut, 22mm, 180 Nm, Discard after removal
Remove LH tie rod end from knuckle
Remove RH front wheel

Note
5x nuts, 21mm, 175 Nm
Remove nut securing the RH tie rod end to the knuckle

Note
1x nyloc nut, 22mm, 180 Nm, Discard after removal
Remove RH tie rod end from knuckle
Raise vehicle fully and lower lift onto locks

Note
Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
Remove outer fasteners from front aero shield

Note
7x bolts, 10mm, 5 Nm
Remove remaining nuts and remove front aero shield from vehicle

Note
2x nuts, 15mm, 5 Nm
Remove clips that secure front valance to LH wheel liner

Note
3x clips
Remove clips that secure front valance to RH wheel liner

Note
3x clips
Remove nut securing RH corner of front valance to front fascia

Note
1x nut, 10mm, 3 Nm
Remove clips securing RH corner of front valance to front fascia

Note
2x clips
Remove nut securing LH corner of front valance to front fascia

Note
1x nut, 10mm, 3 Nm
Remove clips securing LH corner of front valance to front fascia

Note
2x clips
Remove clips securing front valance to front fascia and remove front valance

Note
6x clips, Recommend assistance
Remove FDU bypass hose clip from front subframe

Note
1x clip
Remove clip securing front harness to front subframe

Note
1x clip
Disconnect connectors from horn assembly

Note
2x connectors
Remove bolts securing front end carrier to LH front subframe crash can assembly

Note
2x bolts, 13mm, 16 Nm
Remove bolts securing front end carrier to RH front subframe crash can assembly

Note
2x bolts, 13mm, 16 Nm
Loosen the bolts securing securing front subframe to LH front subframe crash can assembly

Note
2x bolts, 15mm, 53 Nm, This will help when installing the subframe
Loosen the bolts securing securing front subframe to RH front subframe crash can assembly

Note
2x bolts, 15mm, 53 Nm, This will help when installing the subframe
Remove nut securing front stabar link to LH front stabar

Note
1x nyloc nut, 18mm, 98 Nm, Counter hold ball joint with T40, Discard after removal
Move LH front stabar link assembly aside

Note
May need to move the stabilizer bar up/down to get the correct angle needed to remove end link
Remove nut securing front stabar to RH front stabar link assembly

Note
1x nyloc nut, 18mm, 98 Nm, Counter hold ball joint with T40, Discard after removal
Move RH front stabar link assembly aside

Note
May be necessary to pull down on the sway bar to allow the end link to disengage
Remove bolt and nut securing LH front lower comp link to front subframe

Note
1x bolt, 21mm, 1x nut, 21mm, 115 Nm
Move the LH front lower comp link aside
Remove bolts securing LH front lower lateral link to front subframe

Note
2x bolts, 21mm, 115 Nm
Remove bolt and nut securing LH strut to LH front lower lateral link

Note
1x bolt, 21mm, 1x nut, 21mm, 106 Nm
Remove bolt and nut securing RH front lower comp link to front subframe

Note
1x bolt, 21mm, 1x nut, 21mm, 115 Nm
Move the RH front lower comp link aside
Remove bolts securing RH front lower lateral link to front subframe

Note
2x bolts, 21mm, 115 Nm
Remove bolt and nut securing RH strut to lower control arm and move the RH front lower lateral link aside

Note
1x bolt, 21mm, 1x nut, 21mm, 106 Nm
Move the subframe lifting tool underneath the front subframe area
Connect air supply to subframe lifting tool
Position and support the front subframe with subframe lifting tool

Note
Recommend assistance, Latch the subframe to subframe lifting tool, Make sure to align the two guides
Remove bolt securing LH mid mount to body

Note
1x bolt, 15mm, 50 Nm, Discard after removal
Remove bolt securing RH mid mount to body

Note
1x bolt, 15mm, 50 Nm, Discard after removal
Remove LH bolt securing the front portion of the front subframe to body

Note
1x bolt, 18mm, 72 Nm, Discard after removal
Remove RH bolt securing the front portion of the front subframe to body

Note
1x bolt, 18mm, 72 Nm, Discard after removal
Remove LH smaller bolt securing the rear portion of the front subframe to body

Note
1x bolt, 15mm, 50 Nm, Discard after removal
Remove RH smaller bolt securing the rear portion of the front subframe to body

Note
1x bolt, 15mm, 50 Nm, Discard after removal
Remove LH larger bolt securing the rear portion of the front subframe to body

Note
1x bolt, 21mm, 125 Nm, Discard after removal
Remove RH larger bolt securing the rear portion of the front subframe to body

Note
1x bolt, 21mm, 125 Nm, Discard after removal
Lower the subframe from vehicle

Note
Recommend assistance
Disconnect air supply from subframe lifting tool
Remove subframe lifting tool from under vehicle
Position lifting tool and subframe under vehicle for installation
Connect air supply to subframe lifting tool
Raise support tool until the front subframe and body meet

Note
Recommend assistance, Guide the motor mount bushings into the motor mount isolators as the lift is being raised into position, Make sure to line up the rear locating pins on the subframe
Loosely install the RH larger bolt securing rear portion of the front subframe to body

Note
1x bolt, 21mm, 125 Nm, Install new bolt
Loosely install the LH larger bolt securing rear portion of the front subframe to body

Note
1x bolt, 21mm, 125 Nm, Install new bolt
Loosely install the RH smaller bolt securing rear portion of the front subframe to body

Note
1x bolt, 15mm, 50 Nm, Install new bolt
Loosely install the LH smaller bolt securing rear portion of the front subframe to body

Note
1x bolt, 15mm, 50 Nm, Install new bolt
Loosely install RH bolt securing the front portion of the front subframe to body

Note
1x bolt, 18mm, 72 Nm, Install new bolt, Adjust subframe lifting tool if necessary
Loosely install LH bolt securing the front portion of the front subframe to body

Note
1x bolt, 18mm, 72 Nm, Install new bolt, Adjust subframe lifting tool if necessary
Loosely install bolt securing the RH mid mount to body

Note
1x bolt, 15mm, 50 Nm, Install new bolt
Loosely install bolt securing the LH mid mount to body

Note
1x bolt, 15mm, 50 Nm, Install new bolt
Loosely install the bolts securing front end carrier to RH front subframe crash can assembly

Note
2x bolts, 13mm, 16 Nm
Loosely install the bolts securing front front end carrier to LH front subframe crash can assembly

Note
2x bolts, 13mm, 16 Nm
Torque the RH larger bolt securing the rear portion of the front subframe to body

Note
1x bolt, 21mm, 125 Nm
Torque the LH larger bolt securing the rear portion of the front subframe to body

Note
1x bolt, 21mm, 125 Nm
Torque the RH smaller bolt securing the rear portion of the front subframe to body

Note
1x bolt, 15mm, 50 Nm
Torque the LH smaller bolt securing the rear portion of the front subframe to body

Note
1x bolt, 15mm, 50 Nm
Torque the RH bolt securing the front portion of the front subframe to body

Note
1x bolt, 18mm, 72 Nm
Torque the LH bolt securing the front portion of the front subframe to body

Note
1x bolt, 18mm, 72 Nm
Torque the bolt securing the RH mid mount to body

Note
1x bolt, 15mm, 50 Nm
Torque the bolt securing the LH mid mount to body

Note
1x bolt, 15mm, 50 Nm
Torque the bolts securing securing front subframe to RH front subframe crash can assembly

Note
2x bolts, 15mm, 53 Nm
Torque the bolts securing LH front subframe crash can assembly to front subframe

Note
2x bolts, 15mm, 53 Nm
Torque the bolts securing front end carrier to RH front subframe crash can assembly

Note
2x bolts, 13mm, 16 Nm
Torque the bolts securing front end carrier to LH front subframe crash can assembly

Note
2x bolts, 13mm, 16 Nm
Lower the subframe lifting tool from the vehicle

Note
Unlatch the subframe lifting tool from front subframe
Disconnect air supply from subframe lifting tool
Remove the subframe lifting tool from vehicle
Install the RH front lower lateral link and loosely install bolt and nut securing RH strut to lower control arm

Note
1x bolt, 21mm, 1x nut, 21mm, 106 Nm
Loosely install bolts securing RH front lower lateral link to front subframe

Note
2x bolts, 21mm, 115 Nm, Recommend assistance if necessary, Use punch tool to align the fasteners
Install the RH front lower comp link to front subframe
Install bolt and nut securing RH front lower comp link to front subframe

Note
1x bolt, 21mm, 1x nut, 21mm, 115 Nm, Recommend assistance if necessary
Torque bolts securing RH front lower lateral link to front subframe

Note
2x bolts, 21mm, 115 Nm, Recommend assistance if necessary, Use punch tool to align the fasteners
Install LH front lower lateral link and loosely install bolt and nut securing LH strut to lower lateral link

Note
1x bolt, 21mm, 1x nut, 21mm, 106 Nm
Loosely install bolts securing LH front lower lateral link to front subframe

Note
2x bolts, 21mm, 115 Nm, Recommend assistance if necessary, Use punch tool to align the fasteners
Install LH front lower comp link to front subframe
Install bolt and nut securing LH front lower comp link to front subframe

Note
1x bolt, 21mm, 1x nut, 21mm, 115 Nm, Recommend assistance if necessary
Torque bolts securing LH front lower lateral link to front subframe

Note
2x bolts, 21mm, 115 Nm
Position the RH front stabar link assembly to front stabar

Note
May be necessary to pull down on the sway bar to allow the end link to engage
Install nut securing front stabar to RH front stabar link assembly

Note
1x nyloc nut, 18mm, 98 Nm, Install new nyloc nut, Counter hold ball joint with T40, Mark with paint pen
Position LH front stabar link assembly to front stabar

Note
May be necessary to pull down on the sway bar to allow the end link to engage
Install nut securing front stabar link to LH front stabar

Note
1x nyloc nut, 18mm, 98 Nm, Install new nyloc nut, Counter hold ball joint with T40, Mark with paint pen
Connect horn assembly connectors

Note
2x connectors
Install FDU bypass hose clip to front subframe

Note
1x clip
Install clip securing front harness to front subframe

Note
1x clip
Position front valance to front fascia and install clips securing front valance to front fascia

Note
6x clips, Recommend assistance
Install clips securing LH corner of front valance to front fascia

Note
2x clips
Install nut securing LH corner of front valance to front fascia

Note
1x nut, 10mm, 3 Nm
Install clips securing RH corner of front valance to front fascia

Note
2x clips
Install nut securing RH corner of front valance to front fascia

Note
1x nut, 10mm, 3 Nm
Install clips to secure front valance to LH wheel liner

Note
3x clips
Install clips to secure front valance to RH wheel liner

Note
3x clips
Position the front aero shield to vehicle and install nuts

Note
2x nuts, 15mm, 5 Nm
Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front aero shield

Note
7x bolts, 10mm, 5 Nm
Lower vehicle partially and set onto locks

Note
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
Position RH front tie rod end to RH front knuckle
Install nut securing RH front tie rod end to RH front knuckle

Note
1x nyloc nut, 22mm, 180 Nm, Install new nyloc nut
Position LH tie rod end to LH front knuckle
Install nut securing LH front tie rod end to LH front knuckle

Note
1x nyloc nut, 22mm, 180 Nm, Install new nyloc nut
Remove the bolt that attaches the LH front brake rotor to the hub.
Install the hub jack adapter onto the LH front hub and hand-tighten the lug nuts.
Use an underhoist stand to support the hub jack adapter.
Measure the distance between the bottom of the fender and the center of the front axle and adjust the underhoist stand so that the front suspension is set to ride height.
Tighten the bolt and nut that attach the LH front damper to the lower control arm, and then mark the bolt and nut with a paint pen.
106 Nm (78.2 lbs-ft)
Remove the underhoist stand from underneath the LH front suspension.
Remove the lug nuts that attach the hub jack adapter, and then remove the hub jack adapter from the vehicle.
Install the bolt that attaches the LH front brake rotor to the hub.
5 Nm (3.7 lbs-ft)
Repeat step 130 through 137 for the RH side of the vehicle.
Install RH front wheel

Note
5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
Install LH front wheel

Note
5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
Lower vehicle until tires are touching the ground

Note
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Torque RH front wheel

Note
5x nuts, 21mm, 175 Nm
Torque LH front wheel

Note
5x nuts, 21mm, 175 Nm
Install RH front wheel cap

Note
1x cap, Align valve stem with wheel cap cavity
Install LH front wheel cap

Note
1x cap, Align valve stem with wheel cap cavity
Connect the steering gear assembly connectors

Note
2x locking connectors, Engage locking tab
Connect logic connectors to steering gear assembly

Note
2x connectors, Engage locking tab
Slide the intermediate shaft assembly downward to install it to the steering gear assembly

Note
Ensure the intermediate shaft is aligned and fully seated, Recommend assistance if necessary to align the shaft to steering gear
Install bolt securing the intermediate shaft assembly to the steering gear assembly

Note
1x bolt, 13mm, 18 Nm
Connect first responder loop and 12V negative terminal

Note
1x nut, 10mm, 6 Nm, 1x connector, Connect FRL first before connecting 12V to avoid damage to car computer
Install frunk assembly into vehicle

Note
6x clips, Replace any clips if broken or missing
Install fasteners securing the frunk assembly

Note
5x bolts, 10mm, 5 Nm, Newer vehicles may be equipped with 1x push clip securing frunk to washer bottle neck
Install access panel

Note
3x clips, 1x connector
Install rear apron

Note
14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
Close hood
Remove vehicle from lift

Note
Lower rack arms fully and remove from under vehicle if necessary, Remove air suspension from "Jack Mode" if equipped
Remove the steering wheel holder
Raise LH front window
Close LH front door
Check tire pressures

Note
4x tires, Set to specification if necessary, Refer to the "Tire and Loading Information" label located on the driver side B-pillar
Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.

Model Y Service Manual

Subframe Assembly - Front (RWD) (Remove and Install)

Figure 1

Figure 2

Figure 3