22/05/2024 15:03:27

Insulator - Wheelhouse - Set (Remove & Replace)

Correction code 15307402 1.1 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2023-10-09: Updated the reference for removing/installing the rear fascia assembly.
  • 2023-10-10: Added a caution to not manually close the charge port door.
  • 1076927-00-A Hioki Tester
  • 1054720-00-A Portable Bench
  • 1060071-00-A Torque Wrench 1/4in Dr Hexagon
  • 1076928-00-A Test Probes - Hioki 9461

Remove

  1. Open all doors and lower all windows.
  2. Remove the 2nd row seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  3. Remove the HEPA filter assembly. See Assembly - Filter - HEPA (Remove and Replace).
  4. Open the charge port door and the liftgate.
  5. Perform Vehicle HV Disablement Procedure. See Vehicle HV Disablement Procedure.
  6. Remove the LH trunk side trim. See Trim - Side - Trunk - LH (Remove and Replace).
  7. Remove the RH trunk pocket bracket. See Bracket - Trunk Pocket - LH (Remove and Replace).
  8. Fold the 2nd row RH seatback down.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not put weight on the seat in folded position without cushion present, in case of bending the locator tab on the frame.
  9. Remove the RH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  10. Disconnect the 2nd row LH seat connector.
  11. Remove the busbar connector. See Connector - DC Input - Busbar - Charge Port to HV Battery (Remove and Replace).
  12. Release the RH body harness clip from the C-pillar, and then remove the harness backwards from the body.
  13. Disconnect the rear fascia harness, and then remove the rear fascia assembly. See Fascia - Rear (Remove and Install).
  14. Release the clips (x4) to remove the rear body harness from the rear fascia center bracket.
  15. Disconnect the rear BLE connector.
    Tip: Do not push down the red tab. Pull it to disengage the lock, and hold and pull it again to release the connector.
  16. Disconnect the connectors (x2) that attach the rear subframe and the LH rear electrical parking brake (EPB).
  17. Push the rear subframe portion of the LH body harness into the trunk which is near the rear section of the LH rear wheel liner area, and then push the harness through the LH side trunk bulkhead.
  18. Remove the subwoofer assembly. See Subwoofer (Remove and Replace).
  19. Release the clips (x2) that attach the RH body harness to the RH side trunk bulkhead.
  20. Disconnect the connectors (x2) that attach the rear subframe and the RH rear electrical parking brake (EPB).
  21. Push the RH side trunk bulkhead grommet through the RH side trunk bulkhead and thread the harness through the grommet.
  22. Remove the LH and the RH rear wheelhouse insulator from the vehicle.

Install

  1. Install the LH and the RH rear wheelhouse insulator to the vehicle.
  2. Install the grommet to the RH side trunk bulkhead.
  3. Connect the connectors (x2) that attach the rear subframe and the RH rear electrical parking brake (EPB).
  4. Push the rear harness seal into the trunk which is near the rear section of the LH rear wheel liner area, and then push the seal through the body and the fully seat.
  5. Connect the connectors (x2) that attach the rear subframe and the LH rear electrical parking brake (EPB).
  6. Connect the rear BLE connector.
  7. Install the clips (x4) to install the rear body harness onto the rear fascia center bracket.
  8. Connect the rear fascia harness, and then install the rear fascia assembly. See Fascia - Rear (Remove and Install).
  9. Install the harness forward to the body, and then secure the RH body harness clip to the C-pillar.
  10. Install the busbar connector. See Connector - DC Input - Busbar - Charge Port to HV Battery (Remove and Replace).
  11. Reconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  12. Install the HEPA filter assembly. See Assembly - Filter - HEPA (Remove and Replace).
  13. Close the liftgate and the charge port door.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not try to manually close the charge port door.
  14. Raise all windows and close all doors.