17/10/2022 09:53:28

Center Console (2.0) (Structural Pack) (Remove and Install)

Correction code 15190121 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Open all the doors and lower all the windows.
  2. Move the driver seat rearward.
  3. Remove the driver floormat.
  4. Remove the LH center console side panel. See Side Panel - Center Console - LH (Remove and Replace).
  5. Remove the bolt that attaches the LH side of the center console to the instrument panel.
    6.5 Nm (4.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T30 socket
  6. Repeat step 2 through step 4 for the RH side of the vehicle.
  7. Disconnect the USB harness electrical connector at the right front of the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    The connector is located behind the RH center console side bracket.
  8. Remove the bolt that attaches the RH side of the center console to the instrument panel.
    6.5 Nm (4.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T30 socket
  9. Move the front seats forward.
  10. Remove the center console lower rear panel. See Panel - Lower Rear - Center Console (Remove and Replace).
  11. Remove the bolts (x2) that attach the center console to the lower rails.
    9.5 Nm (7.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
  12. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  13. Disconnect LV power. See 12V/LV Power (Disconnect and Connect).
  14. Disconnect the center console harness electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    The connector is located behind the LH center console side carpet.
  15. Slide the center console assembly rearward and out of the riser rails.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Take note of the surrounding components to avoid personal injury and vehicle damage.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Force applied must be parallel to the rails.
    Tip: Use the cupholders to pull the console rearward. Shift center console from side to side to loosen if necessary.
  16. With assistance, remove the center console from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify the rotating lids are in the closed position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Tilt the rear of console upward, and then pull the assembly towards the rear of vehicle to remove.

Install

  1. With assistance, position the center console onto the rails, and then push the assembly forward.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Force applied must be parallel to the rails.
  2. Connect the center console harness electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    The connector is located behind the LH center console side carpet.
  3. Connect LV power. See 12V/LV Power (Disconnect and Connect).
  4. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  5. Install the bolts (x2) that attach the center console to the lower rails.
    9.5 Nm (7.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
  6. Install the center console lower rear panel. See Panel - Lower Rear - Center Console (Remove and Replace).
  7. Move the front seats rearward.
  8. Install the bolt that attaches the RH side of the center console to the instrument panel.
    6.5 Nm (4.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T30 socket
  9. Connect the USB harness electrical connector at RH front of the center console.
  10. Install the RH center console side panel. See Side Panel - Center Console - LH (Remove and Replace).
  11. Install front passenger floor mat.
  12. Move the front passenger seat to the original position.
  13. Install the bolt that attaches the LH side of the center console to the instrument panel.
    6.5 Nm (4.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T30 socket
  14. Install the LH center console side panel. See Side Panel - Center Console - LH (Remove and Replace).
  15. Install driver floor mat.
  16. Move the driver seat to the original position.
  17. Raise all the windows and close all the doors.