17/05/2023 10:01:09

Seatbelt - 2nd Row - LH (7 Seat) (Remove and Replace)

Correction code 20056122 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Move the driver seat forward.
  3. Open the LH rear door and lower the LH rear window.
  4. Move the LH 2nd row seat back assembly forward.
  5. Open the liftgate.
  6. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  7. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  8. Remove the rear load floor. See Trunk Load Floor - Rear (Remove and Replace).
  9. Release the clips (x4) that attach the LH side of the trunk sill trim to the vehicle, and then partially release the LH side of the trunk sill trim.
  10. Remove the LH load floor bracket. See Bracket - Trunk Load Floor - LH (Remove and Replace).
  11. Remove the LH trunk pocket bracket. See Bracket - Trunk Pocket - LH (Remove and Replace).
  12. Release the upper portion of the LH trunk side trim.
  13. Release the clips (x6) that attach the upper C-pillar trim, and then set the trim aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Guide the front upper corner groove out of the headliner.
  14. Remove and discard the bolt that attaches the 2nd row LH lower seat belt anchor to the body.
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
    • 3 in extension
  15. Release the clips that attach the guide bezel to the LH upper C-pillar trim, and then separate the bezel from the seat belt.
  16. Feed the seat belt through the LH upper C-pillar trim, and then remove the trim.
  17. Release the connector lock, and then disconnect the LH 2nd row seat belt connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift the red locking tab, and then release the connector.
  18. Remove and discard the bolt that attaches the LH 2nd row seatbelt to the body, and then remove the seatbelt from the vehicle.
    30 Nm (22.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket

Install

  1. Position the LH 2nd row seatbelt into the vehicle, and then install a new bolt that attaches the seatbelt to the body.
    30 Nm (22.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Note the position of the locating tabs.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
  2. Connect the LH 2nd row seat belt connector, and then engage the connector lock.
  3. Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  4. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  5. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  6. Move the driver seat to the original position.
  7. Raise the LH front window and close the LH front door.
  8. Move LH 2nd row seat back to the original position.
  9. Raise the LH rear window and close the LH rear door.
  10. Close the liftgate.