28/05/2024 04:34:38

Bracket - Brake Caliper - Rear - LH (Remove and Replace)

Correction code 33010532 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-05-28: Updated references and cautions.

Torque Specifications

Table 1. Torque Specifications: Bracket - Brake Caliper - Rear - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the LH rear brake caliper to the LH rear brake caliper bracket
26.5 Nm (19.5 lbs-ft)
  • 14 mm socket
Reuse
Bolts (x2) that attach the LH rear brake caliper bracket to the LH rear knuckle
83 Nm (61.2 lbs-ft)
  • External Torx E18
Replace

Remove

  1. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  2. Place the vehicle into EPB Service Mode. See Parking Brake - Caliper - Rear - LH (Release).
  3. Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
  4. Remove the bolts (x2) that attach the LH rear brake caliper to the LH rear brake caliper bracket.
    26.5 Nm (19.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 14 mm socket
  5. Remove the LH rear caliper from the assembly, and then support it with an S-hook in a secure location.
  6. Remove the LH rear brake pads (x2) from the LH rear brake caliper bracket.
  7. Remove the LH rear brake caliper bracket abutment clips (x4).
  8. Remove and discard the bolts (x2) that attach the LH rear brake caliper bracket to the LH rear knuckle, and then remove the bracket from the knuckle.
    83 Nm (61.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • External Torx E18

Install

  1. Position the LH rear brake caliper bracket to the LH rear knuckle, and then install new bolts (x2) that attach the bracket to the knuckle.
    83 Nm (61.2 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    To prevent damage to the flexible brake hose, make sure that the brake hose can bend forward and does not make contact with the wheel arch liner when the vehicle is lowered.
    Tip: Use of the following tool(s) is recommended:
    • External Torx E18
  2. Install the LH rear brake caliper bracket abutment clips (x4).
  3. Apply an even layer of Silaramic lubricant to the top and bottom of the LH brake pad contact points.
  4. Install the LH rear brake pads (x2) into the LH rear brake caliper bracket.
  5. Install the bolts (x2) that attach the LH rear brake caliper to the LH rear brake caliper bracket.
    26.5 Nm (19.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 14 mm socket
  6. Install the LH rear wheel. See Wheel Assembly (Remove and Install).
  7. Press and hold the Park button to release EPB Service Mode.
  8. Remove the vehicle from the lift. See Raise Vehicle - 2 Post Lift.
  9. Perform a road test to ensure proper brake pedal feel and performance.
    Informational PurposesAn informational icon, calling your attention
    Note
    Per current FRT (00040100).