06/07/2023 18:31:05

Underhood Storage Unit (Remove and Replace)

Correction code 15240702 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2023-04-04: Added check for proper routing of and possible damage to HVIL harness branch.

Torque Specifications

Table 1. Torque Specifications: Underhood Storage Unit (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Underhood storage unit to body fasteners
5 Nm (3.7 lbs-ft)
  • 10 mm socket
  • ¼ in std ratchet
  • 2 in extension
Reuse

Remove

  1. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  2. Remove the underhood storage unit access panel. See Access Panel - Underhood Storage Unit (Remove and Replace).
  3. Remove the underhood storage unit carpet.
  4. Remove the bolts that attach the underhood storage unit to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • ¼ in std ratchet
    • 2 in extension
  5. Release the clip that attaches the underhood storage unit to the washer fluid reservoir neck.
  6. Release the clips (x4) that attach the underhood storage unit to the vehicle, and then remove the underhood storage unit from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any broken or missing clips, if reinstalling the same underhood storage unit.
  7. Inspect the HVIL harness branch of the A/C compressor HV harness.
    1. Make sure that the harness does not rest on the shock tower brace where it crosses over to the connector on the LH shock tower.
      Figure 1. Harness improperly routed over the shock tower brace
    2. Inspect the condition of the HVIL harness that it has not been crushed and insulation worn to expose the bare wire.
      Figure 2. Harness crushed
      Figure 3. Insulation worn
    3. If a wire has been damaged, perform an electrical harness repair as a separate activity. Refer to the Service Documents page for more information.
      Warning IconA warning icon, calling your attention to a possibly risky situation
      CAUTION
      Make sure there is sufficient slack in the repaired harness so that there is no stress in the connector on the LH shock tower.
  8. If the same underhood storage unit is to be reinstalled, this procedure is finished. If a new underhood storage unit is be installed, continue to the next step.
  9. Remove the tow hook from the underhood storage unit.

Install

  1. If the same underhood storage unit removed is being installed, skip to step 3. If a new underhood storage unit is being installed, continue to the next step.
  2. Install the tow hook into the underhood storage unit.
  3. Make sure that the HVIL harness branch of the A/C compressor HV harness is properly routed away from and does not rest upon the shock tower brace.
    Figure 4. Harness properly routed away from the shock tower brace
  4. Install the underhood storage unit into the vehicle, and then fasten the clips (x4) that attach the underhood storage unit to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure that all clips for the underhood storage unit are engaged.
  5. Fasten the clip that attaches the underhood storage unit to the washer fluid reservoir neck.
  6. Install the bolts (x4) that attach the underhood storage unit to the vehicle.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • ¼ in std ratchet
    • 2 in extension
  7. Install the underhood storage unit carpet.
  8. Install the underhood storage unit access panel. See Access Panel - Underhood Storage Unit (Remove and Replace).
  9. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).