2021-02-19
Actuator - Floor Latch - 2nd Row Seat - RH (7-Seat) (Remove and Replace)
Correction code
13020062
0.42
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when
performing the below procedure.
Remove
- Remove the RH 2nd row seat assembly. See Seat Assembly - 2nd Row - RH (7-Seat) (Remove and Replace).
- Remove the RH 2nd row seat toe kick cover.
- Remove the clip that attaches the RH 2nd row seat side shield to the cushion pan.
-
Release the clip that attaches the RH 2nd row seat side shield to the RH
2nd row seat assembly, and then lift the shield up to release it from the
assembly.
NoteDo not pull the shield away from the assembly as there is still an electrical connector connected
- Disconnect the RH 2nd row seat side shield electrical connector, and then remove the shield from the assembly.
- Release the clips (x4) that attach the RH 2nd row seat outer B-cover from the inner B-cover, and slide the cover towards the rear of the seat to remove it from the assembly.
- Fold the seat to the upright position.
-
Remove the screw that attaches the RH 2nd row seat inner B-cover to the
cushion pan.1.5 Nm (1.1 lbs-ft)TIpUse of the following tool(s) is recommended:
- Torx T25 socket
- Flex head ratchet/flex head torque wrench
- Release the hook that attaches the inner B-cover to the RH 2nd row seat assembly.
- Release the clips that attach the RH 2nd row seat cushion harness to the podium.
- Remove the clip that attaches the RH 2nd row seat cushion pan to the seat frame.
- Slightly lift the RH 2nd row seat cushion pan upward, but do not fully remove the cushion at this time.
- Release the RH 2nd row seat floor latch actuator cable from the RH floor latch.
- Release the RH 2nd row seat floor latch actuator cable from the LH floor latch.
- Disconnect the RH 2nd row seat floor latch actuator electrical connector.
-
Remove the bolts that attach the RH 2nd row seat floor latch actuator to
the assembly, and then remove the actuator from the assembly.2.5 Nm (1.8 lbs-ft)TIpUse of the following tool(s) is recommended:
- 8 mm hex
- Flex head ratchet/flex head torque wrench
- 4 in extension
Install
-
Position the RH 2nd row seat
onto the cushion pan, and then install the bolts.2.5 Nm (1.8 lbs-ft)TIpUse of the following tool(s) is recommended:
- 8 mm hex
- Flex head ratchet/flex head torque wrench
- 4 in extension
- Connect the RH 2nd row seat floor latch actuator electrical connector.
- Install the RH 2nd row seat floor latch actuator cable onto the LH floor latch.
- Install the RH 2nd row seat floor latch actuator cable onto the RH floor latch.
- Push downward on the RH 2nd row seat cushion to fully seat the cushion to the frame.
- Install the clip that attaches the RH 2nd row seat cushion pan to the seat frame.
- Fasten the clips that attach the RH 2nd row seat cushion harness to the podium.
- Fasten the hook that attaches the inner B-cover to the RH 2nd row seat assembly.
-
Install the screw that
attaches the RH 2nd row seat inner B-cover to the cushion pan.1.5 Nm (1.1 lbs-ft)TIpUse of the following tool(s) is recommended:
- Torx T25 socket
- Flex head ratchet/flex head torque wrench
- Disconnect the RH 2nd row seat recliner actuator electrical connector.
- Using the seat fold tool, connect the recliner actuator electrical connector into the recliner actuator, and then activate the switch to fold the RH 2nd row seat down.
- Disconnect the seat fold tool from the RH 2nd row seat.
- Connect the RH 2nd row seat recliner actuator electrical connector.
- Position the RH 2nd row seat outer B-cover onto the inner B-cover, and then install the clips (x4).
- Connect the RH 2nd row seat side shield electrical connector.
- Position the RH 2nd row seat side shield onto the RH 2nd row seat assembly, and then install the clip.
- Install the clip that attaches the RH 2nd row seat side shield to the cushion pan.
- Install the RH 2nd row seat toe kick cover.
- Install the RH 2nd row seat assembly. See Seat Assembly - 2nd Row - RH (7-Seat) (Remove and Replace)