06/06/2024 09:40:12

Filter - Cabin (Remove and Replace)

Correction code 18100102 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-06-06: Added cabin filter health score reset for SW versions 2024.14+
  • 2024-04-09: Updated procedures to accommodate cabin filter covers with top screws and bottom screws.

Torque Specifications

Table 1. Torque Specifications: Filter - Cabin (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screw that attaches the cabin filter cover to the HVAC module
1.2 Nm (.9 lbs-ft)
  • 6 mm socket
  • Flex head ratchet/flex head torque wrench
  • 4 in extension
Reuse

Remove

Figure 1. Animated demonstration for cabin filter cover with top screw
Figure 2. Animated demonstration for cablin filter cover with bottom screw
  1. Remove the RH side center console side panel carpet. See Side Panel - Center Console - LH (Remove and Replace).
  2. Use the clip tool to remove tabs Release RH footwell assembly from IP.
  3. Inspect how the cabin filter cover is attached to the HVAC unit.
  4. If the cabin filter cover is attached with tabs: Release the tab at the bottom of the cabin filter cover, and then remove the cover from the HVAC unit.
  5. If the cabin filter cover is attached with a screw at the top of the cover: Remove the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  6. If the cabin filter cover is attached with a screw regardless if at the top or bottom of the cover: Remove the screw that attaches the cabin filter cover to the HVAC unit, and then remove the cover from the unit.
    Tip: Use of the following tool(s) is recommended:
    • 6 mm socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
  7. Fold the filter tabs outward, and then pull the upper filter out of the filter housing.
  8. After the upper filter is removed, raise the lower filter up and out of the filter housing.

Install

  1. Install the lower filter into the filter housing, with the arrows pointing to the rear of the vehicle.
  2. Install the upper filter into the filter housing, with the arrows pointing to the rear of the vehicle, and then fold the filter tabs inward.
  3. If the cabin filter cover is attached with a screw regardless if at the top or bottom of the cover: Install the cabin filter cover on the HVAC unit, and then install the screw that attaches the cabin filter cover to the HVAC unit.
    1.2 Nm (.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Engage the lower cover tab before fastening the cover.
    Tip: Use of the following tool(s) is recommended:
    • 6 mm socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
  4. If the cabin filter cover is attached with a screw at the top of the cover: Install the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  5. If the cabin filter cover is attached with tabs: Install the upper tab of the cabin filter cover in the slot of the HVAC unit, and then install the lower tab of the cabin filter cover.
  6. Install the RH side center console side panel carpet. See Side Panel - Center Console - LH (Remove and Replace).
  7. Check whether the vehicle cabin and HEPA filter health score requires reset: On the vehicle touchscreen, touch Controls (vehicle icon) > Software, and then scroll down to display the vehicle software version.
    • If the vehicle software version is older than 2024.14, the cabin filter health score does not need to be reset. Skip to the next step in this procedure.
    • If the vehicle software version is 2024.14 or newer:
      1. Enable Service Mode. See Service Mode.
      2. If the cabin filter was replaced: In the Service Mode menu, touch Thermal (snowflake icon) > HVAC > Right, and then touch Cabin Filter > Reset Cabin Filter Score.
      3. If the HEPA filter elements or assembly were replaced, touch HEPA Filter > Reset HEPA Filter Score.
      4. The cabin and/or HEPA filter health score is now reset. Continue to the next step in this procedure.
    Figure 3. Reset cabin filter health score for Model Y
    Figure 4. Reset HEPA filter health score for Model Y