31/01/2024 16:25:03

Shell - Backrest - 2nd Row - LH (7-Seat) (Remove and Replace)

Correction code 13082712 0.78 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning

This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Open all four doors
Lower all four windows
Move LH front seat forward
Move RH front seat forward
Partially remove LH rear door seal
Remove LH 7s Lower C-Pillar Trim

Note
8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim
Fold down 2nd row 60 seatback assembly

Note
Press button, fold forwards
Disconnect 2nd row 60 seat connector

Note
1x connector
Move 60 seat forward using towel bar

Note
With one hand on towel bar pull up and slide the seat forward with your other hand
Remove 60 seat rear outboard track fastener

Note
1x patch bolt, 11mm, 37 Nm, Discard after removal
Remove 60 seat rear inboard track fasteners

Note
2x patch bolts, 11mm, 37 Nm, Discard after removal
Move 60 seat fully rearward using towel bar

Note
With one hand on towel bar pull up and slide the seat forward with your other hand
Remove 60 seat outboard track cover

Note
1x clip, Slide covers forward to release from 60 seat tracks
Remove center track cover from 2nd row seats

Note
2x clips, Slide covers forward to release from 2nd row seat tracks
Release cabin carpet from 60 seat

Note
Pull cabin carpet towards front of vehicle
Remove 60 seat front inboard track fasteners

Note
1x bolts, 11mm, 37 Nm, Discard after removal
Remove 2nd row 60 seat frame front outboard track fasteners

Note
1x bolts, 11mm, 37 Nm, Discard after removal
Remove 2nd row 60 seat assembly from vehicle

Note
Recommend assistance
Remove front push clip from 2nd row 60 cushion assembly outer side shield

Note
1x clip, Use pick to remove the push clip from the bottom side of the outboard cover
Remove 2nd row 60 cushion assembly outer side shield

Note
1x clip 1x connector, Remove outer side shield assembly by pulling outwards and up at the front portion of the trim, Unclip remaining clip and unplug the connection
Remove 2nd row 60 seatback assembly toe kick panel

Note
7x clips, Pry up on LH side of 60 toe kick cover to release clips, Repeat on RH side to fully remove
Release clips and remove inboard outer trim from 2nd row 60 seat cushion assembly

Note
3x clips, Use trim tool to unclip 3x clips and remove inboard outer trim towards rear of the vehicle
Remove 2nd row 60 seatback panel

Note
9x clips, 2x hooks, Release clips starting at the top of back panel working your way down the lower back panel, pull 60 back panel towards front of vehicle to remove
Remove 2nd row center seat switch

Note
1x connector, 2x clips, Using plastic trim tool pry the top of the switch away from 20 back panel to ease removal
Remove center back panel from 2nd row center seatback

Note
5x clips, 2 hooks, Lift up at the lower 20 back panel and then slide forward to release
Release 2nd row 60 seat harness connectors and clip from seat frame

Note
1x clip, 7x connectors
Disconnect seat cables from easy entry actuators on 60 seat

Note
4x clips
Remove cable from 60 fold actuator

Note
1x clip, Remove cable from 60 fold actuator
Remove push clips for 2nd row 60 bottom seat pan

Note
2x clips, Remove push clips from front of seat pan
Remove center seatback lumbar bun fastener

Note
1x screw, T20, 1.5 Nm
Remove center seatback lumbar bun

Note
2x clips, Pull bolster outwards to release
Remove center seatback pivot clamps

Note
2x bolts, T40, 22 Nm, Once fasteners are removed slide pivot clamp towards the center of center seatback and pull each outwards to remove
Remove center seatback from 60 seat frame

Note
Remove center seatback by lifting upwards
Manually release the center seatback latch

Note
Use small screwdriver to manipulate the center seatback latch to release
Remove fasteners securing 60 seat pan to seat frame

Note
4x fastener, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Remove remaining bolts attaching seat pan to seat frame
Remove headrest from 2nd row 60 seatback assembly

Note
Simultaneously depress the guide button and insert a 90 degree pick into the guide opening, Lift up while engaged
Remove headrest guides from 2nd row 60 seatback assembly

Note
Pull back on lower portion of the headrest guide to release tab while also applying upward force to remove headrest guides
Remove 2nd row 60 seatback assembly

Note
4x clips, Release clips securing 60 seatback and lift upwards, Seat belt will be removed in a later step
Remove 2nd row 60 seat cushion assembly

Note
Remove seat bottom by lifting the rear first and removing it towards front of the seat
Remove 2nd row center seat belt anchor

Note
1x bolt, T50, 40 Nm, Discard after removal
Remove 2nd row center seat belt guide

Note
2x clips, 2x datums
Remove 2nd row center seat belt from 2nd row 60 seatback assembly

Note
Pass seat belt through opening
Place 2nd row 60 seatback assembly on a suitable working surface

Note
Avoid damage to seat cover
Remove easy-entry switch

Note
2x clips, 1x connector
Disconnect seat heating connector

Note
1x connector
Release 2nd row 60 seatback cover

Note
16x tabs, Pull material downward to release
Remove backrest shell from 2nd row 60 seatback cover

Note
Early production models may have staples holding material to shell in some areas
Remove wiring harness from backrest shell

Note
3x harness clips, 5x tabs
Install wiring harness to backrest shell

Note
3x harness clips, 5x tabs
Install 2nd row 60 seatback cover to backrest shell

Note
16x hooks, Pull material downward to attach, Ensure material is distributed correctly on visible face
Connect heating pad connector

Note
1x connector
Install easy-entry switch

Note
2x tabs, 1x connector
Install 2nd row center seat belt to 2nd row 60 seatback assembly

Note
Pass seat belt through opening
Install 2nd row center seat belt guide

Note
2x clips, 2x datums
Install 2nd row center seat belt anchor

Note
1x bolt, T50, 40 Nm
Place 60 seat pan onto seat frame

Note
Reinstall seat bottom onto seat frame by starting at the rear of the seat
Secure 60 seat bottom to seat frame

Note
4x fasteners, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Install remaining bolts attaching seat pan to seat frame
Install 2nd row 60 seatback into place

Note
4x clips, Slide seat back into place making sure the bottom retainers slide into place, Reinstall push clips to secure seat back
Install headrest guides into 60 seat assembly

Note
Install headrest guides by pressing downwards until lower tab is seated
Install headrest onto 60 seat assembly

Note
Push down to secure
Install center seatback pivot clamps

Note
2x bolts, T40, 22 Nm, Insert pivot clamp at center of center frame and slide outwards to install fasteners, When replacing pivot clamps they must be replaced in pairs
Install center seatback lumbar bun

Note
2x clips, Press seatback lumbar bun into center frame
Install center seatback lumbar bun fastener

Note
1x screw, T20, 1.5 Nm
Plug in connector and install trim to 60 seat

Note
1x connector, 1x clip, Plug in connector and install trim by hooking the front into place and seat clip at rear of trim.
Install push clip at front of outer 60 side shield assembly

Note
1x clip, Install push clip at front bottom side of the trim
Install inboard outer trim to 60 seat

Note
Clips 3x, Install inboard outer trim and re-seat 3x clips
Insert back panel hooks into center seat back assembly

Note
2x hooks, Engage hooks and slide rearward into position, Early production have 4x hooks
Install center back panel onto seat back

Note
5x clips
Install 2nd row center seat switch

Note
1x connector, 2x clips
Install 60 toe kick cover

Note
7x clips
Install LH seatback onto 60 seat assembly

Note
9x clips, 4 hooks, Attach hooks onto frame rail, Work upwards and fasten all the clips
Install 2nd row 60 seat assembly

Note
Recommend assistance
Connect 2nd row 60 seat connector

Note
1x connector
Install fasteners securing 60 seat frame to body

Note
5x patch bolts, 11mm, 37 Nm, Install new patch bolts, Bottom seat bolts located behind main carpet, Torque in sequence; Outboard front -> Both inboard rear -> Outboard rear -> Inboard front
Secure cabin carpet to 60 seat

Note
Strap velcro on
Move 2nd row 60 seatback to vertical position

Note
Remove seat back protection if necessary
Install 60 seat outboard track cover

Note
1x clip
Install 60 seat outboard track cover

Note
1x clip
Install LH 7s Lower C-Pillar Trim

Note
8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim
Re-seat LH rear door seal

Note
Seat pillar and sill trim tabs underneath seal
Move the RH front seat to its original position.
Move LH front seat to original position

Note
This can also be achieved by selecting driver profile via UI
Raise all four windows
Close all four doors

Note
If 12V is powered up, Unlatch rear doors before closing

Model Y Service Manual

Shell - Backrest - 2nd Row - LH (7-Seat) (Remove and Replace)

Figure 1

Figure 2

Figure 3