2022-12-22

Harness - Subframe - Rear (Remove and Replace)

Correction code 17102002 1.14 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  2. Disconnect the 12V power. See 12V/LV Power (Disconnect and Connect).
  3. Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  4. Remove the front trunk load floor. See Trunk Load Floor - Front (Remove and Replace).
  5. Remove the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  6. Remove the LH and RH load floor bracket. Bracket - Trunk Load Floor - LH (Remove and Replace).
  7. Remove the rear trunk carpet. See Tub - Rear Trunk (Remove and Replace).
  8. Remove the mid aero shield. See Panel - Aero Shield - Mid (Remove and Replace).
  9. Remove the rear fascia diffuser. See Diffuser - Rear Fascia (Remove and Replace).
  10. Remove the clip that secures the LH rear wheel speed harness connector to the rear subframe.
  11. Disconnect the LH rear wheel speed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use mechanical hands to hold the connector end on the subframe harness side.
  12. Remove the clip that secures the RH rear wheel speed harness connector to the rear subframe.
  13. Disconnect the RH rear wheel speed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use mechanical hands to hold the connector end on the subframe harness side.
  14. Disconnect the RH side 12V subframe harness connector.
  15. Remove the clips (x3) that secure the RH side 12V subframe harness to the body and subframe.
  16. Disconnect the LH side 12V subframe harness connector.
  17. Remove the clips (x3) that secure LH side 12V subframe harness to the body and subframe.
  18. Disconnect the rear drive unit 12V connector.
  19. Remove the rear drive unit 12V harness clip.
  20. Disconnect the harness from the ride height sensor (if equipped).
    Informational PurposesAn informational icon, calling your attention
    Note
    Press the locking tab on the right side of the connector and pull down to release.
  21. Remove the harness clip from the ride height sensor (if equipped).
  22. Disconnect the resolver connector from the rear drive unit.
  23. Disconnect the oil pump connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not push down on the red tab, pull the red tab to disengage the lock and pull again to release the connector.
  24. Release clips (x4) that secure the subframe harness to the top of rear subframe.
  25. Release the clips (x2) that secure the subframe harness to the left and right of the subframe.
  26. Remove the harness from the gap of the body and subframe.

Install

  1. Insert the harness from the gap of the body and subframe.
  2. Install the rear subframe harness in place and install the clips (x2) that secure the subframe harness to the left and right of the subframe.
  3. Install the clips (x4) that secure the subframe harness to the top of the subframe.
  4. Connect the resolver connector to the rear drive unit.
  5. Connect the oil pump connector.
  6. Install the rear drive unit 12V harness clip.
  7. Install the rear drive unit 12V connector.
  8. Install the harness clip to the ride height sensor (if equipped).
  9. Connect the harness to the ride height sensor (if equipped).
  10. Connect the LH rear wheel speed sensor.
  11. Install the clip that secures the LH rear wheel speed sensor connector to the subframe.
  12. Connect the RH rear wheel speed harness.
  13. Install the clip that secures the RH rear wheel speed harness connector to the subframe.
  14. Install the clips (x3) that secure the LH side 12V subframe harness to the body and subframe.
  15. Connect the LH side 12V subframe harness connector.
  16. Install the clips (x3) that secure the RH side 12V subframe harness to the body.
  17. Connect the RH side 12V subframe harness connector.
  18. Install the rear fascia diffuser. See Diffuser - Rear Fascia (Remove and Replace).
  19. Install the mid aero shield. See Panel - Aero Shield - Mid (Remove and Replace).
  20. Connect the 12V power. See 12V/LV Power (Disconnect and Connect).
  21. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  22. Install the rear trunk carpet. See Tub - Rear Trunk (Remove and Replace).
  23. Install the LH and RH load floor bracket. Bracket - Trunk Load Floor - LH (Remove and Replace).
  24. Install the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  25. Install the front trunk load floor. See Trunk Load Floor - Front (Remove and Replace).
  26. Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).