21/04/2021 10:04:45

Seat Track - Inner - 2nd Row Seat - RH (7-Seat) (Remove and Replace)

Correction code 13020322 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Remove the RH 2nd row seat assembly. See Seat Assembly - 2nd Row - RH (7-Seat) (Remove and Replace).
  2. Release the clips that attach the RH 2nd row seat toe kick cover to the seat assembly, and then remove the cover from the assembly.
  3. Remove the clip that attaches the RH 2nd row seat side shield to the cushion pan.
  4. Release the clip that attaches the RH 2nd row seat side shield to the RH 2nd row seat assembly, and then lift the shield up to release it from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not pull the shield away from the assembly as there is still an electrical connector connected
  5. Disconnect the RH 2nd row seat side shield electrical connector, and then remove the shield from the assembly.
  6. Release the clips (x4) that attach the RH 2nd row seat outer B-cover from the inner B-cover, and slide the cover towards the rear of the seat to remove it from the assembly.
  7. Fold the seat to the upright position.
  8. Remove the screw that attaches the RH 2nd row seat inner B-cover to the cushion pan.
    1.5 Nm (1.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
  9. Release the hook that attaches the inner B-cover to the RH 2nd row seat assembly.
  10. Release the clips that attach the RH 2nd row seat cushion harness to the seat podium.
  11. Remove the clip that attaches the RH 2nd row seat cushion pan to the seat frame.
  12. Slightly lift the RH 2nd row seat cushion pan upward, but do not fully remove the cushion at this time.
  13. Disconnect the RH 2nd row seat recliner actuator electrical connector.
  14. Using the seat fold tool, connect the recliner actuator electrical connector into the recliner actuator, and then activate the switch to release the floor latches.
  15. Disconnect the seat fold tool from the RH 2nd row seat.
  16. Connect the RH 2nd row seat recliner actuator electrical connector.
  17. Position the RH 2nd row seat on its RH side.
  18. Remove the bolts that attach the RH 2nd row seat podium to the seat tracks.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
    • Flex head ratchet/flex head torque wrench
  19. With assistance, remove the RH 2nd row seat podium from the seat track.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use one hand to engage the towel bar, and then move the inner seat track rearward with the other hand until the groove on the seat podium releases from the inner seat track. Lift the podium to remove it from the seat track.
  20. Release the RH 2nd row seat easy entry actuator cable from the LH easy entry latch.
  21. Remove the nuts that attach the RH 2nd row seat inner seat track to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
    • 6 in extension
  22. Remove the RH 2nd row seat inner seat track from the seat frame assembly, and then release the towel bar from the outer seat track.
    Informational PurposesAn informational icon, calling your attention
    Note
    The inner seat track will be removed with the towel bar. The towel bar is spring loaded. Place one hand over the towel bar lever securing the towel bar to the inner seat track. Remove the inner seat track, and then lift the towel bar upwards to disengage it from the outer seat track.
  23. Remove the towel bar from the RH 2nd row seat inner seat track.

Install

  1. Position the spring and towel bar into the seat track, and then rotate the towel bar until it is properly placed inside the holding tabs.
  2. Install the RH 2nd row towel bar into the RH 2nd row seat inner seat track, and then install the inner seat track into the seat frame assembly.
  3. Install the RH 2nd row seat inner seat track into the seat frame assembly, and then install the nuts.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
    • 6 in extension
  4. Install the RH 2nd row seat easy entry actuator cable into the LH easy entry latch.
  5. With assistance, install the RH 2nd row seat podium onto the seat track.
    Informational PurposesAn informational icon, calling your attention
    Note
    Install the groove on the podium onto the outer seat track, and then align the groove on the podium onto the inner seat track. Engage the towel bar with one hand, and then move the inner seat track inward until the groove on the podium engages the seat track.
  6. Install the bolts that attach the RH 2nd row seat podium to the seat tracks.
    37 Nm (27.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
    • Flex head ratchet/flex head torque wrench
  7. Position the RH 2nd row seat onto the seat tracks and floor latches.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push downward on the seat frame assembly to latch the floor latches.
  8. Fully seat the RH 2nd row seat cushion assembly onto the seat frame.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to pinch the actuator cables or cushion harness.
  9. Install the clip that attaches the RH 2nd row seat cushion pan to the seat frame.
  10. Fasten the clips that attach the RH 2nd row seat cushion harness to the podium.
  11. Fasten the hook that attaches the inner B-cover to the RH 2nd row seat assembly.
  12. Install the screw that attaches the RH 2nd row seat inner B-cover to the cushion pan.
    1.5 Nm (1.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
  13. Disconnect the RH 2nd row seat recliner actuator electrical connector.
  14. Using the seat fold tool, connect the recliner actuator electrical connector into the recliner actuator, and then activate the switch to fold the RH 2nd row seat down.
  15. Disconnect the seat fold tool from the RH 2nd row seat.
  16. Connect the RH 2nd row seat recliner actuator electrical connector.
  17. Position the RH 2nd row seat outer B-cover onto the inner B-cover, and then install the clips (x4).
  18. Connect the RH 2nd row seat side shield electrical connector.
  19. Position the RH 2nd row seat side shield onto the RH 2nd row seat assembly, and then install the clip.
  20. Install the clip that attaches the RH 2nd row seat side shield to the cushion pan.
  21. Install the RH 2nd row seat toe kick cover.
  22. Install the RH 2nd row seat assembly. See Seat Assembly - 2nd Row - RH (7-Seat) (Remove and Replace).