23/02/2023 08:45:42

Carpet - Front - RH (Structural Pack) (Remove and Replace)

Correction code 15301122 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Remove

  1. Remove the RH mid A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  2. Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  3. Remove the RH center console side panel. See Side Panel - Center Console - LH (Remove and Replace).
  4. Remove the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  5. Move the RH front seat fully forward.
  6. Remove and discard the bolts (x2) that attach the rear of the 1st row RH seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • 3/8 in std flex head ratchet
    • 3/8 in flex head torque wrench (installation only)
    Figure 1. LH shown; RH similar
  7. Move the RH front seat fully rearward.
  8. Remove and discard the bolts (x2) that attach the front of the 1st row RH seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • 3/8 in std flex head ratchet
    • 3/8 in flex head torque wrench (installation only)
  9. Position the RH front seat up and carefully tilt the seat backwards.
  10. Release the clips (x2) that attach the RH front carpet to the cabin support.
  11. Release the clips (x4) that attach the RH front carpet underneath the RH front seat.
    Figure 2. Seat removed for clarity
  12. Release the seat harness clip and harness, release all edges, and then remove the RH front carpet from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take note of the short edge under the center console.

Install

  1. Position the RH front carpet into the vehicle, and then secure the seat harness clip and harness and all edges.
    Informational PurposesAn informational icon, calling your attention
    Note
    Tuck the short edge underneath the center console.
  2. Install the clips (x4) that attach the RH front carpet underneath the RH front seat.
    Figure 3. Seat removed for clarity
  3. Install the clips (x2) that attach the RH front carpet to the cabin support.
  4. Carefully position the RH front seat down.
  5. Install the new bolts (x2) that attach the front of the 1st row RH seat to the body.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • 3/8 in std flex head ratchet
    • 3/8 in flex head torque wrench (installation only)
    Figure 4. LH shown; RH similar
  6. Move the RH front seat fully forward.
  7. Install the new bolts (x2) that attach the rear of the 1st row RH seat to the body.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • 3/8 in std flex head ratchet
    • 3/8 in flex head torque wrench (installation only)
    Figure 5. LH shown; RH similar
  8. Install the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  9. Install the RH center console side panel. See Side Panel - Center Console - LH (Remove and Replace).
  10. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  11. Install the RH mid A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  12. Move the RH front seat to the original position.