10/12/2024 08:21:33

Seatbelt - 2nd Row - LH (5 Seat) (Remove and Replace)

Correction code 20056102 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-12-10: Fixed incorrect torque values for retractor to body fastener.

Torque Specifications

Table 1. Torque Specifications: Seatbelt - 2nd Row - LH (5 Seat) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the 2nd row LH lower seat belt anchor to the body
35 Nm (25.8 lbs-ft)
  • 15 mm socket
  • 3 in extension
Replace
Bolt that attaches the seat belt retractor to the body
30 Nm (22.1 lbs-ft)
  • 13 mm socket
  • 3 in extension
Replace

Remove

  1. Open the LH doors and lower the LH windows.
  2. Move the driver seat to its foremost position.
  3. Fold the LH rear passenger seat back down.
  4. Open the rear liftgate.
  5. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  6. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  7. Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  8. Remove the front trunk load floor. See Trunk Load Floor - Front (Remove and Replace).
  9. Remove the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  10. Remove the LH load floor bracket. See Bracket - Trunk Load Floor - LH (Remove and Replace).
  11. Remove the LH trunk pocket bracket. See Bracket - Trunk Pocket - LH (Remove and Replace).
  12. Remove the LH trunk side trim. See Trim - Side - Trunk - LH (Remove and Replace).
  13. Remove the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  14. Remove and discard the bolt that attaches the 2nd row LH lower seat belt anchor to the body.
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
    • 3 in extension
  15. Release the clips (x2) that attach the bezel to the LH rear upper C-pillar trim, and then slide the bezel off the seat belt.
  16. Guide the seat belt through the LH rear upper C-pillar trim, and the remove the trim from the vehicle.
  17. Release the connector lock, and then disconnect the electrical connector from the 2nd row LH seat belt retractor.
  18. Remove and discard the bolt that attaches the 2nd row LH seat belt retractor to the body, and then remove the retractor from the vehicle.
    Tip: Use of the following tool(s) is recommended:

Install

  1. Install the 2nd row LH seat belt retractor to the body, and then install a new bolt to attach the retractor to the body.
    30 Nm (22.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
  2. Connect the electrical connector to the 2nd row LH seat belt retractor, and then engage the connector lock.
  3. Install the bezel onto the seat belt, and then attach the clips (x2) to the LH rear upper C-pillar trim.
  4. Install a new bolt that attaches the 2nd row LH lower seat belt anchor to the body.
    35 Nm (25.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
    • 3 in extension
  5. Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  6. Install the LH trunk side trim. See Trim - Side - Trunk - LH (Remove and Replace).
  7. Install the LH trunk pocket bracket. See Bracket - Trunk Pocket - LH (Remove and Replace).
  8. Install the LH load floor bracket. See Bracket - Trunk Load Floor - LH (Remove and Replace).
  9. Install the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  10. Install the front trunk load floor. See Trunk Load Floor - Front (Remove and Replace).
  11. Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  12. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  13. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  14. Move the driver seat to its original position.
  15. Close the LH front door and raise the LH front window.
  16. Fold the LH rear passenger seat back to its original position.
  17. Close the LH rear door and raise the LH rear window.
  18. Close the rear liftgate.