31/01/2024 16:25:04

Seatbelt - 2nd Row - Center (7 Seat) (Remove and Replace)

Correction code 20056322 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Open RH front and rear doors
  2. Lower all four windows
  3. Move LH front seat forward
  4. Move RH front seat forward
  5. Partially remove LH rear door seal
  6. Remove LH 7s Lower C-Pillar Trim
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim
  7. Fold down 2nd row 60 seatback assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Press button, fold forwards
  8. Disconnect 2nd row 60 seat connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  9. Move 60 seat forward using towel bar
    Informational PurposesAn informational icon, calling your attention
    Note
    With one hand on towel bar pull up and slide the seat forward with your other hand
  10. Remove 60 seat rear outboard track fastener
    Informational PurposesAn informational icon, calling your attention
    Note
    1x patch bolt, 11mm, 37 Nm, Discard after removal
  11. Remove 60 seat rear inboard track fasteners
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, 11mm, 37 Nm, Discard after removal
  12. Move 60 seat fully rearward using towel bar
    Informational PurposesAn informational icon, calling your attention
    Note
    With one hand on towel bar pull up and slide the seat forward with your other hand
  13. Remove 60 seat outboard track cover
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, Slide covers forward to release from 60 seat tracks
  14. Remove center track cover from 2nd row seats
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Slide covers forward to release from 2nd row seat tracks
  15. Release cabin carpet from 60 seat
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull cabin carpet towards front of vehicle
  16. Remove 60 seat front inboard track fasteners
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolts, 11mm, 37 Nm, Discard after removal
  17. Remove 2nd row 60 seat frame front outboard track fasteners
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolts, 11mm, 37 Nm, Discard after removal
  18. Remove 2nd row 60 seat assembly from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  19. Remove front push clip from 2nd row 60 cushion assembly outer side shield
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, Use pick to remove the push clip from the bottom side of the outboard cover
  20. Remove 2nd row 60 cushion assembly outer side shield
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip 1x connector, Remove outer side shield assembly by pulling outwards and up at the front portion of the trim, Unclip remaining clip and unplug the connection
  21. Remove 2nd row 60 seatback assembly toe kick panel
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, Pry up on LH side of 60 toe kick cover to release clips, Repeat on RH side to fully remove
  22. Release clips and remove inboard outer trim from 2nd row 60 seat cushion assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips, Use trim tool to unclip 3x clips and remove inboard outer trim towards rear of the vehicle
  23. Remove 2nd row 60 seatback panel
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, 2x hooks, Release clips starting at the top of back panel working your way down the lower back panel, pull 60 back panel towards front of vehicle to remove
  24. Remove 2nd row center seat switch
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 2x clips, Using plastic trim tool pry the top of the switch away from 20 back panel to ease removal
  25. Remove center back panel from 2nd row center seatback
    Informational PurposesAn informational icon, calling your attention
    Note
    5x clips, 2 hooks, Lift up at the lower 20 back panel and then slide forward to release
  26. Release 2nd row 60 seat harness connectors and clip from seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 7x connectors
  27. Disconnect seat cables from easy entry actuators on 60 seat
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  28. Remove cable from 60 fold actuator
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, Remove cable from 60 fold actuator
  29. Remove push clips for 2nd row 60 bottom seat pan
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Remove push clips from front of seat pan
  30. Remove center seatback lumbar bun fastener
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 1.5 Nm
  31. Remove center seatback lumbar bun
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Pull bolster outwards to release
  32. Remove center seatback pivot clamps
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T40, 22 Nm, Once fasteners are removed slide pivot clamp towards the center of center seatback and pull each outwards to remove
  33. Remove center seatback from 60 seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove center seatback by lifting upwards
  34. Manually release the center seatback latch
    Informational PurposesAn informational icon, calling your attention
    Note
    Use small screwdriver to manipulate the center seatback latch to release
  35. Remove fasteners securing 60 seat pan to seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    4x fastener, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Remove remaining bolts attaching seat pan to seat frame
  36. Remove headrest from 2nd row 60 seatback assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Simultaneously depress the guide button and insert a 90 degree pick into the guide opening, Lift up while engaged
  37. Remove headrest guides from 2nd row 60 seatback assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull back on lower portion of the headrest guide to release tab while also applying upward force to remove headrest guides
  38. Remove 2nd row 60 seatback assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, Release clips securing 60 seatback and lift upwards, Seat belt will be removed in a later step
  39. Remove 2nd row 60 seat cushion assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove seat bottom by lifting the rear first and removing it towards front of the seat
  40. Remove 2nd row center seat belt anchor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, T50, 40 Nm, Discard after removal
  41. Remove 2nd row center seat belt guide
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 2x datums
  42. Remove 2nd row center seat belt from 2nd row 60 seatback assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Pass seat belt through opening
  43. Remove 2nd row center seat belt retractor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x tab, 1x bolt, T50, 40 Nm
  44. Install 2nd row center seat belt retractor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x tab, 1x bolt, T50, 40 Nm
  45. Install 2nd row center seat belt to 2nd row 60 seatback assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Pass seat belt through opening
  46. Install 2nd row center seat belt guide
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 2x datums
  47. Install 2nd row center seat belt anchor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, T50, 40 Nm
  48. Place 60 seat pan onto seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    Reinstall seat bottom onto seat frame by starting at the rear of the seat
  49. Secure 60 seat bottom to seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    4x fasteners, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Install remaining bolts attaching seat pan to seat frame
  50. Install 2nd row 60 seatback into place
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, Slide seat back into place making sure the bottom retainers slide into place, Reinstall push clips to secure seat back
  51. Install headrest guides into 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Install headrest guides by pressing downwards until lower tab is seated
  52. Install headrest onto 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Push down to secure
  53. Install center seatback pivot clamps
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T40, 22 Nm, Insert pivot clamp at center of center frame and slide outwards to install fasteners, When replacing pivot clamps they must be replaced in pairs
  54. Install center seatback lumbar bun
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Press seatback lumbar bun into center frame
  55. Install center seatback lumbar bun fastener
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 1.5 Nm
  56. Plug in connector and install trim to 60 seat
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 1x clip, Plug in connector and install trim by hooking the front into place and seat clip at rear of trim.
  57. Install push clip at front of outer 60 side shield assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, Install push clip at front bottom side of the trim
  58. Install inboard outer trim to 60 seat
    Informational PurposesAn informational icon, calling your attention
    Note
    Clips 3x, Install inboard outer trim and re-seat 3x clips
  59. Insert back panel hooks into center seat back assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x hooks, Engage hooks and slide rearward into position, Early production have 4x hooks
  60. Install center back panel onto seat back
    Informational PurposesAn informational icon, calling your attention
    Note
    5x clips
  61. Install 2nd row center seat switch
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 2x clips
  62. Install 60 toe kick cover
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips
  63. Install LH seatback onto 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, 4 hooks, Attach hooks onto frame rail, Work upwards and fasten all the clips
  64. Install 2nd row 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  65. Connect 2nd row 60 seat connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  66. Install fasteners securing 60 seat frame to body
    Informational PurposesAn informational icon, calling your attention
    Note
    5x patch bolts, 11mm, 37 Nm, Install new patch bolts, Bottom seat bolts located behind main carpet, Torque in sequence; Outboard front -> Both inboard rear -> Outboard rear -> Inboard front
  67. Secure cabin carpet to 60 seat
    Informational PurposesAn informational icon, calling your attention
    Note
    Strap velcro on
  68. Move 2nd row 60 seatback to vertical position
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove seat back protection if necessary
  69. Install 60 seat outboard track cover
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  70. Install 60 seat outboard track cover
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  71. Install LH 7s Lower C-Pillar Trim
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim
  72. Re-seat LH rear door seal
    Informational PurposesAn informational icon, calling your attention
    Note
    Seat pillar and sill trim tabs underneath seal
  73. Move the RH front seat to its original position.
  74. Move LH front seat to original position
    Informational PurposesAn informational icon, calling your attention
    Note
    This can also be achieved by selecting driver profile via UI
  75. Raise all four windows
  76. Close all four doors
    Informational PurposesAn informational icon, calling your attention
    Note
    If 12V is powered up, Unlatch rear doors before closing