21/12/2022 13:28:01

Trim - Seat Back – 2nd Row – RH (Remove and Replace)

Correction code 13082202 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the RH front door and lower the RH front window.
  2. Open the RH rear door.
  3. Move the front passenger seat fully forward.
  4. Remove the RH 2nd row seat outer bolster. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  5. Fold the RH 2nd row seat back to the down position.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the seat cushion is not present, protect the seat as required.
  6. Disconnect the RH 2nd row seat back harness electrical connector.
  7. Release the clip that attaches the RH 2nd row seat back harness to the pivot bracket.
  8. Remove the RH 2nd row seat back panel. See Back Panel – 2nd Row Seat – RH (Remove and Replace).
  9. Remove the RH 2nd row headrest. See Headrest - 2nd Row - LH (Remove and Replace).
  10. Remove the LH and RH 2nd row backrest guide locks. See Guide Lock - Headrest - 2nd Row (Remove and Replace).
  11. Remove the bolts (x2) that attach the RH 2nd row backrest cushion to the back frame.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
  12. Fold the RH 2nd row seat back to the vertical position, but do not latch the seat back.
  13. Release the clips (x8), disconnect the backrest harness electrical connector, and then remove the RH 2nd row backrest cushion from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the upper clips first to disconnect backrest the connector.
  14. Disconnect the RH 2nd row seat back substrate harness electrical connectors (x2).
  15. Release the hooks that attach the bottom portion of the RH 2nd row seat back trim to the RH 2nd row seat back insert.
    Informational PurposesAn informational icon, calling your attention
    Note
    Negotiate the trim under the harness.
  16. Release the clips (x2) that attach the RH 2nd row backrest cushion heat pad harness to the seat back insert.
  17. Release the clips (x5) that attach the RH 2nd row seat back trim to the RH 2nd row seat back insert.
    Informational PurposesAn informational icon, calling your attention
    Note
    Negotiate the clips around the substrate harness.
  18. Release the hooks (x6) and clips (x2) that attach the top portion of RH 2nd row seat back trim to the RH 2nd row seat back insert.
  19. Pull the top portion of RH 2nd row seat back trim down and off the RH 2nd row seat back insert.
  20. Remove the RH 2nd row seat back insert from the cushion assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Negotiate the heat pad harness under the substrate harness.
  21. Release the velcro that attaches the RH 2nd row seat back trim to the 2nd row seat back foam until the hog rings are visible.
  22. Use diagonal cutters to cut the hog rings (x3) that attach the RH 2nd row seat back trim to the 2nd row seat back foam.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push down on the foam to allow access to rings.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove any excess hog ring pieces.
  23. Remove the RH 2nd row seat back trim from the seat back foam.

Install

  1. Position the RH 2nd row seat back trim onto the RH 2nd row seat back foam.
  2. Use hog ring pliers to crimp the hog rings (x3) to secure the RH 2nd row seat back trim to the 2nd row seat back foam.
    Informational PurposesAn informational icon, calling your attention
    Note
    Place the hog ring into the hog ring pliers prior to installation.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push down on foam to allow access if necessary.
  3. Secure the velcro that attaches the RH 2nd row seat back trim to the 2nd row seat back foam.
  4. Install the RH 2nd row seat back insert into the cushion assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Negotiate the heat pad harness under the substrate harness.
  5. Pull the top portion of RH 2nd row seat back trim up and onto the RH 2nd row seat back insert.
  6. Secure the hooks (x6) and clips (x2) that attach the top portion of RH 2nd row seat back trim to the RH 2nd row seat back insert.
  7. Secure the clips (x5) that attach the RH 2nd row seat back trim to the RH 2nd row seat back insert.
    Informational PurposesAn informational icon, calling your attention
    Note
    Negotiate the clips around the substrate harness.
  8. Secure the clips (x2) that attach the RH 2nd row backrest cushion heat pad harness to the seat back insert.
  9. Secure the hooks (x2) that attach the bottom portion of the RH 2nd row seat back trim to the RH 2nd row seat back insert.
    Informational PurposesAn informational icon, calling your attention
    Note
    Negotiate the trim under the harness.
  10. Connect the RH 2nd row seat back substrate harness electrical connectors (x2).
  11. Position the RH 2nd row backrest cushion onto the RH 2nd row backrest, connect the backrest harness electrical connector, and then secure the clips (x8) that attach the cushion to the backrest.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the lower clips first, then connect backrest harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure all clips are properly seated.
  12. Fold the RH 2nd row seat back to the down position.
  13. Install the bolts (x2) that attach the RH 2nd row backrest cushion to the back frame.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
  14. Install the LH and RH 2nd row backrest guide locks. See Guide Lock - Headrest - 2nd Row (Remove and Replace).
  15. Install the RH 2nd row headrest. See Headrest - 2nd Row - LH (Remove and Replace).
  16. Install the RH 2nd row seat back panel. See Back Panel – 2nd Row Seat – RH (Remove and Replace).
  17. Install the clip that attaches the RH 2nd row seat back harness to the pivot bracket.
  18. Connect the RH 2nd row seat back harness electrical connector.
  19. Fold the RH 2nd row seat to the up position.
  20. Install the RH 2nd row seat side bolster. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  21. Close the RH rear door.
  22. Restore the front passenger seat back to its original position.
  23. Raise the RH front window and close the RH front door.