17/06/2022 13:05:40

Latch - Door - Front - LH (Remove and Replace)

Correction code 113510020.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Remove the LH front door trim decor. See .
  2. Remove the LH front door trim panel. See Panel - Door Trim - Front - LH (Remove and Replace)
  3. Remove the remaining clip retainers from the LH front door.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of retainers will vary with each removal.
  4. Remove the bolts (x6) that attach the LH front door closeout panel from the door assembly, release the closeout panel from the door assembly, and then route the handle cable through the closeout panel to remove it from the assembly.
    4.5 Nm (3.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • 2 in extension
  5. Connect the window master switch to the LH front door harness, and then fully raise the LH front window.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connect the door panel x927 if the switch kit is not available.
  6. Remove and discard the bolts (x2) that attach the LH front door latch to the door assembly.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T45 socket
    • Flex head ratchet/flex head torque wrench
  7. Release the clips (x2) that attach the LH front door release cable and harness to the door assembly.
  8. Release the connector lock, and then disconnect the LH front door latch assembly electrical connector.
  9. Carefully maneuver the LH front door latch assembly around the window regulator, and then remove it from the vehicle.

Install

  1. Carefully maneuver the LH front door latch assembly around the window regulator into position, and then route the release cable underneath the door harness assembly.
  2. Connect the LH front door latch assembly electrical connector, and then engage the connector lock.
  3. Install the clips (x2) that attach the LH front door release cable and harness to the door assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the release cable is routed underneath the door harness assembly.
  4. Install new bolts (x2) that attach the LH front door latch to the door assembly.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T45 socket
    • Flex head ratchet/flex head torque wrench
  5. Route the cable through the LH front door closeout panel, position the closeout panel onto the door assembly, and then install the bolts (x6) that attach the closeout panel to the door assembly.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the inner door handle manual release cable is routed properly.
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • 2 in extension
  6. Install the LH front door trim panel. See Panel - Door Trim - Front - LH (Remove and Replace)
  7. Install the LH front door trim decor. See .
  8. Close the LH front door.
  9. Check the gap fitment of LH front door decor to the IP decor.
    Informational PurposesAn informational icon, calling your attention
    Note
    Refer to CVIS for current specification targets.
  10. Open the LH front door.
  11. Turn the adjustment nut to adjust the LH front door trim as necessary.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 18 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • 6 in extension
    • Torx T30 socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Loosen the T30 nut and rotate the nut to achieve desired specification. Rotate clockwise to close the gap, and counterclockwise to tighten the gap. Torque the T30 fastener to lock.
  12. Install the LH front door trim decor. See .
  13. Check the gap fitment of LH front door decor to the IP decor.
    Informational PurposesAn informational icon, calling your attention
    Note
    Refer to CVIS for current specification targets.
  14. Close the LH front door.