06/09/2022 14:58:32

Surround - Handle - Liftgate (Remove and Replace)

Correction code 15110062 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Apply masking tape around the liftgate tail lights and applique.
  2. Remove the LH and RH rear fog/reverse lights. See Light - Fog/Reverse - Rear - LH (Remove and Replace).
  3. Remove the bolts (x3) that attach the liftgate applique bracket to the liftgate, and then separate bracket from the liftgate.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 bit
  4. Release the clips (x5) that attach the liftgate tail light and applique bracket assembly to the liftgate body.
    Informational PurposesAn informational icon, calling your attention
    Note
    The center of the applique is secured by clips. Take care not to damage the applique or body. Rest the bracket on the liftgate.
  5. Remove the bolts (x2) that attach the liftgate handle to the liftgate.
    14.4 Nm (10.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Support the handle from the interior when released.
  6. Disconnect the liftgate handle electrical connector.
  7. Remove the screws (x2) that attach the liftgate handle to the liftgate handle surround.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 bit

Install

  1. Position the liftgate handle onto the liftgate handle surround, and then install the screws (x2) that attach the handle to the surround.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 bit
  2. Connect the liftgate handle electrical connector.
  3. Position the liftgate handle onto the liftgate, and then install the bolts (x2) that attach the handle to the liftgate.
    14.4 Nm (10.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Support the handle from the interior.
  4. Secure the clips (x5) that attach the liftgate tail light and applique bracket assembly to the liftgate body.
  5. Secure the liftgate applique bracket, and then peel off the red tape as needed.
  6. Install the bolts (x3) that attach the liftgate applique bracket to the liftgate.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 bit
  7. Install the LH and RH rear fog/reverse lights. See Light - Fog/Reverse - Rear - LH (Remove and Replace).
  8. Remove all masking tape and hold down tools from the liftgate
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove after time has been allotted for the applique to properly adhere. Suggest minimum of 5 minutes.