Link - Aft - Lower - Front - LH (Remove and Replace)
Correction code 31013602 0.78 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.
Torque Specifications
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Nut that attaches the front lower aft link to the knuckle |
|
|
Replace | PN - 1109263-00-B |
Bolt and nut that attach the front lower aft link to the subframe |
|
|
Reuse | |
Nut and bolt that attach the front air spring module to the front lower aft link |
|
|
Reuse |
Remove
- Remove the LH front wheel. See Wheel Assembly (Remove and Install).
- Raise the vehicle to working height. See Raise Vehicle - 2 Post Lift.
- Remove the front aero shield. See Panel - Aero Shield - Front (Remove and Replace).
-
Remove the nut and bolt that attach
the LH front air spring module to the front lower aft link.
Tip: Use of the following tool(s) is recommended:
- 21 mm socket
- 21 mm combination wrench
-
Remove and discard the nut that
attaches the LH front lower aft link to the knuckle, set aside the Nord-Lock washers,
and then release the link from the knuckle.
NoteNote the positioning and orientation of the Nord-Lock washers.Tip: Counter hold the stud with a T45 socket and use a breaker bar to loosen the nut.Tip: Use of the following tool(s) is recommended:
- 22 mm socket
- Torx T45 socket
- Mark the subframe and aft link bolt to aid with installation.
-
Remove the bolt, nut, and washer that
attach the LH front lower aft link to the subframe, and then remove the link from the
vehicle.Tip: Use of the following tool(s) is recommended:
- 21 mm socket
- 22 mm combination wrench
Install
-
Position the LH front lower aft link
on the vehicle, and then hand-tighten the bolt, nut, and washer that attach the link to
the subframe.CAUTIONDo not torque this joint at this time. This joint will be torqued during the alignment check.NoteAlign the marking on the eccentric bolt with the marking on the subframe.Tip: Use of the following tool(s) is recommended:
- 21 mm socket
- 22 mm combination wrench
-
Position the LH front lower aft link
on the knuckle, and then install the Nord-Lock washers and new nut that attach the link
to the knuckle.Tip: Counter hold the stud with a T45 socket.Tip: Use of the following tool(s) is recommended:
- 22 mm socket
- Torx T45 socket
-
Position the LH front air spring
module on the lower aft link, and then hand-tighten the nut and bolt that attach the air
spring module to the link.CAUTIONDo not torque this joint at this time. This joint will be torqued during the alignment check.Tip: Use of the following tool(s) is recommended:
- 21 mm socket
- 21 mm combination wrench
- Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
- Install the LH front wheel and remove the vehicle from the 2 post lift. See Wheel Assembly (Remove and Install).
- Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.